79090033500 Frigidaire Range - Instructions

Unplugged the range. Removed the top section of the back of the stove to expose switches. Removed the knob, (pulls off exposing the 2 switch screws), unscrew & pull out from the back. The new switch was slightly bigger but the same manufacture and post letters & numbers. Transfer wires one-at-a-time from the old to the new switch. Mount the new switch back in place, put the screws in and the knob on. I plugged in the stove for a quick test, HA....works perfectly. Unplugged again and put the back panel back on, plugged back in and pushed the stove back in it's hole. BEFORE; the old switch when turned down would come back on BUT stay on high, a lot of boil overs. FINALLY: when turned on, it would NOT turn off, a real fire hazard. Thank you for having an original replacement part.

First, make sure power is off to range. Removed backing cover, pulled one wire off infinite switch at a time to put in right place on new switch. Easy fix.

1 - Turn off the power from the panel. 2 - Unplugged the range from outlet. 3 - Unscrewed the black hex screws from the rear panel. 4 - Took a pic of the bad infinite burner switch to ensure the correct wires would connect to the new switch. 5 - Removed knob and unscrewed switch, then replaced with new switch. Matched all of the wires to like, L1, L2, P, H1 and H2. If any wires do not exist for your switch, it is ok because not all ranges use all wires.

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Removed the drawer. Inserted the new glide tab into a hole in the side. Inserted the drawer slides in the the glide. Closed drawer--done! Works fine. Probably only 5-10 minutes.

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

Just use flat screwdriver to press on clip and just squeeze it in

After researching on what exactly to call the part, which was a front drawer glide. I found this out by watching the video. It showed me exactly what I needed and what it looked like. I run to the oven to look at the other one, to make sure thats what I needed, and it looked like the part that I needed (mind you I am a female, and not a repair person), so this video helped me out alot. When the part arrived, I knew how to take the drawer out, and easily snapped the little plastic glide in to place, and slipped the drawer back on the gliders, and it worked perfect, so proud of myself, that I done it by myself, with no help from husband. I bragged and bragged on myself with a big pat on my own back, thanks Part Select, I know what to do when it happens again. Its my fault cause it broke, cause I overload the drawer with pots and pans LOL!!! Brenda Dixon

Switch was easy to replace. Some hex head screws to remove the panel and two screws to remove the switch. Though the plug in positions were totally different, all the quick connect terminals were marked on both switches.

removed back and transferred four wires to new part and replaced back

I removed the drawer, removed and replaced the guides on both sides in the front and replaced the drawer.

The drawer under the oven had been aggravating me for some time. It was titled and did not close right. Finally, I took it out to see what the problem was and noticed that the glides were broken. I googled the model no. of the stove (figuring I would have no luck) and to my great relief was directed to this EXCELLENT site. I ordered the new drawer glides within minutes and they were literally delivered the next day. Snapped right in, fixed, happy!! It's times like this when I can't figure out how we all lived without the internet!

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

I just had to plug the new burner plate in the receptical
and it works again very well.

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.