RE34BAA3 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Sheffield, MA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Found bake element cracked
Read the reviews and followed the same procedure. Very east..took about 10-15 minutes.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Withams, VA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat
My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Temple, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element would not heat.
Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from Boise, ID
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element broke in half due to liquid dripping onto it.
Removed back of stove, removed screws holding old element. attached new element in same place, returned back to stove. My wife pushed element from inside stove into holes, which was a help. Voila! It works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from roslyn, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
haeting element cracked
juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Lykens, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element burned out
Just took the back of the stove off and removed old one and put new one in. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DUSTIN from OGDEN, UT
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element went out ...
Took the back off, and took the terminals off. Took out the old element and put the new one in and put the terminals on and screwed it back in and put the back on. And all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from River Forest, IL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven baking element would not heat up.
First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from North Vernon, IN
- Parts Used:
- 318372211
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No burner
I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fleetwood, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element burnt out
It was really easy. Removed the racks, removed the 2 quarter-inch screws with a nutdriver. Pulled the bad element out about 3-4 inches, enough to unhook the wires attached to the element with spade connectors. Unhooked the wires and removed bad element. Hooked up new element and reversed the process. Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Glenside, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Burned out element
Removed 2 rear screws. Pulled out element. Popped out 2 wire clips. Replaced old element with the new one and attached wire clips. A caveman could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Hayward, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat.
I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fran from Frankfort, KY
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Heating element went out
First, I removed the two screws that hold the element in place. I pulled out the element about 2 inches, and then I wasn't sure what to do, so I called my son and he finished the project in about 5 minutes or less. He pulled off the wires and then put the new element in place, slipped the wires on the new element, then pushed it back into the holes and screwed the screws back in. Worked great.
Was this instruction helpful to you?
Thank you for voting!
replaced drip pans
i removed the stove eye and the old drip pan. then i placed the new drip pan in and replaced the eye. the new drip pans fit way better than the ones that i took off of it.
Was this instruction helpful to you?
Thank you for voting!