79090043601 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alvie from Pasco, WA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
replaced the infinite burner switch
I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronnie from cana, VA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the stove eye would go to high and stay
watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W3Works, from Fairport, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner switch would not disengage, leaving +24VAC to the element.
Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Greenville, TX
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket In Door Replaced
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Smtella from Wappapello, MO
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
My burner would stay on high regardless of where it was set.
We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from NORTH PORT, FL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
no heat in oven
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hiram, OH
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't work
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JILL from VIRDEN, IL
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Large Burner On Glass Top Quit Working
Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from Daleville, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat from bottom or top element,k stove top and clock all worked fine.
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arnold from Carlsbad, CA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
element would not heat.
Replaced the control I got from you , even though it was a little different the lugs matched up and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Glenmoore, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
element light staying lit
Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Acton, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner would stay on and the hi-temp safety limit switch is all that would shut it off.
Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Kingsport, TN
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Large element would only heat on high.
The infinite switch arrived promptly and while not a perfect match fit the range fine. It took me a few extra minutes to figure out the wiring configuration, but it was fairly easy. I was very pleased with Parts Select's service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Madison, AL
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Hot Surface Light won't turn off.
Unplugged stove. Quickly unscrewed back panel (4 screws). Popped the wires off one at a time attaching them to the new switch. Pulled the knob off the front, unscrewed screws, and put new switch in repeating previous steps in reverse. Put the panel back on, plugged it up, and pushed it back into place. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Hillsboro, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch was Sparking
So simple....removed back panel, removed knob from front of range and removed 2 screws holding the knob in. Used needle nose pliers to pull wires off existing switch, placed wires in identical spots on new switch. Put switch post through front of range and put the 2 screws back in and the knob on. Finished and ready to go in less than 10 minutes. No more sparking....
Was this instruction helpful to you?
Thank you for voting!