PLGFZ390ECK Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Herbert from MARIETTA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was over heating temp. of oven keep climbing
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from OWASSO, OK
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven temperature was not consistent.
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from GOLDENDALE, WA
- Parts Used:
- 316489403
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven taking along time to heat up
First thing. If your wife insists on helping buy 2
Because the first one will mysteriously come up broke. Just saying
This is a very easy replacement project. You can do it. TURN POWER OFF TO RANGE BEFORE REPLACING IGNITER Remove a couple screws take the heat shield out. Remove the bottom drawer unplug the igniter remove a couple screws holding the igniter in place. Replace the igniter and screws. Plug in the igniter replace bottom drawer. Screw heat shield back down. Turn power to stove back on. You’re done
Because the first one will mysteriously come up broke. Just saying
This is a very easy replacement project. You can do it. TURN POWER OFF TO RANGE BEFORE REPLACING IGNITER Remove a couple screws take the heat shield out. Remove the bottom drawer unplug the igniter remove a couple screws holding the igniter in place. Replace the igniter and screws. Plug in the igniter replace bottom drawer. Screw heat shield back down. Turn power to stove back on. You’re done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julieta from ELMIRA, NY
- Parts Used:
- 808608804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Gas stove won’t light on half the appliance
First we replaced the wiring harness because a multi-meter said it wasn’t getting power. That was only partially true. The wiring harness was burned looking so we just kept it instead of sending it back. When the spark module got here the burner caps were removed and then the wires were noted where they went on the module and then the power and gas were turned off. The spark module was removed and then the stove was tested and we were back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilma from Syracuse, NY
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom oven plate had foil stuck to it
Very easy to order,part was delivered promptly and installation was easy.I unscrewed a few screws and lifted the bottom panel out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from PORTLAND, OR
- Parts Used:
- 316220009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The know was missing
So easy... just put the knob in place.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darin from O FALLON, MO
- Parts Used:
- 316489403
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven igniter stopped working
When removing the screws that hold the igniter, the screws stripped. Not my first time so I very slowly removed the screws but they still stripped. I had to cut both with a small hacksaw but be careful not to damage the bracket that is welded to the burner. After successfully removing the screws had to go get 5/16 steel self tapping screws to install the new igniter. Use a self tapping screw to thread the hold first then remove and install the igniter with a new screw. Job was a success. Good luck with yours
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dolores from SAN ANTONIO, TX
- Parts Used:
- 316220009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken burner knob
Received new knob simply inserted and it worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from MOORE, OK
- Parts Used:
- 316400603
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Panel finish ruined by tin foil
Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from AKRON, OH
- Parts Used:
- 316400603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement of bottom oven panel
Very simple. I removed the oven racks, loosened the two screws that held the old panel in place, lifted out the old panel and replaced it with the new one, then tightened the screws to hold the new panel in place. It took no more than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from FAYETTEVILLE, NY
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not reach temperature or it would finally reach temp but would not stay warm.
Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclockwise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclockwise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karen from brooklyn, NY
- Parts Used:
- 316220002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my housekeeper broke the stove knob
I was so happy to get the part before Thanksgiving. While I was opening the box I was telling to concierge how fast I got the part. A neighbor overheard me & asked who I used & I tor off the top of the receipt so he could use your company. He said all his knobs are held together w. rubberbands.
The best part was the help finding the serial #. I would have never found it on my own.
Thanks, Karen T
The best part was the help finding the serial #. I would have never found it on my own.
Thanks, Karen T
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERICA from PHILADELPHIA, PA
- Parts Used:
- 316220009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner knob broke.
It was easy to find on the website. It doesn't match exactly, however without the knob the burner will not light. It was literally a snap to snap the knob in place. The part arrive in a timely manner from the USPS. Thank you! I'm encouraged to get one more piece of equipment repaired because of this site thorough service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from NEW ORLEANS, LA
- Parts Used:
- 316400603
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel
Unscrewed old panel/removed and inserting new panel and used same 2 screws to secure in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Naperville, IL
- Parts Used:
- 316220002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The top burner knobs for this range had deformed over time and were discontinued.
Through an extensive web search of parts suppliers, I discovered a top burner knob in production that had the same shaft measurements as the original discontinued model. Once the ordered replacements arrived, it was a simple matter of removal and replacement.
Was this instruction helpful to you?
Thank you for voting!