GLGF386DSH Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- KEITH from CAZADERO, CA
- Parts Used:
- 316411217
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
stovetop was permanently discolored.
Remove surface grates. Use a nutdriver to back out selftapping screws that attach burners to stovetop (apply a solvent oil. These tend to corrode badly and break off. I got lucky and only broke a couple). The stovetop itself is held down by spring tabs. Just pry up at the front and it will pop loose. Lift up at the front and pull out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Trinidad, CO
- Parts Used:
- 5304534663
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
bake burner igniter open circuit--no oven heat
I followed the you tube www.partselect.com. Got door off--easy, and other parts off--easy, as you tube shows--I used the adj wrench to remove old screws--there are two--front one off--easy, the rear one was stripped at factory installation--so got it out, but broke it off in the process. So I had to drill out the part of the screw that remained, and then used a substitute screw (8-32x1/2) on re-assembly. Re-assembly went easy--note that the removal of electrical connection is a "pinch-squeeze" to pull off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma J from Riverview, FL
- Parts Used:
- 5304503232
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
inner glass door was broken
removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Collegeville, PA
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Door glass cracked
Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Louisville, KY
- Parts Used:
- 316557300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Small plastic lens on control panel broken.
Pulled the range out, unplugged it, removed upper back panel, inserted lens through front of control panel, slid the notch on the actual light onto the lip on the back of the plastic lens. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Charlotte, NC
- Parts Used:
- 316220000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob on gas range wore out
I just slapped the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Reno, NV
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
unscrewed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John M. from PLEASANT PRAIRIE, WI
- Parts Used:
- 316490000
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no heat
Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Olathe, KS
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven handle brittle and broke in two.when I dropped a pot on it.
It was easy once I got screws that work.Old screws and handle had machine screws that held handle on.Order screws with handle so you can install immediately...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Gladwin, MI
- Parts Used:
- 316237805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench set
burner would not light
We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Jordan, AR
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven not heating up properly
I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melanie from Reading, PA
- Parts Used:
- 316404500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost a rack?
After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Saint Clair Shores, MI
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sliced Outlet Cord
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Durham, NC
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Aluminium foil fused to the panel
I removed the two back screws, slid out the old panel, then fitted in the new panel (it fit perfectly) and replaced the screws. Five minutes, tops.
Was this instruction helpful to you?
Thank you for voting!