GLGF386DQJ Frigidaire Range - Instructions

It was as easy as removing some screws from the back of the oven and replacing the part. I was worried about not ordering the overlay, since it was mentioned in all the descriptions, but soon found it is exactally what i thought it was, the face of the clock and the buttons that you see on the oven. The one I had was still in good condition and i opted to not replace. I just unpealed the old overlay from the old part, stuck it to the new part and it was good. Make sure you unplug the oven before you start to do anything as these electrical components can easily shock and cause harm!

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!

I followed the you tube www.partselect.com. Got door off--easy, and other parts off--easy, as you tube shows--I used the adj wrench to remove old screws--there are two--front one off--easy, the rear one was stripped at factory installation--so got it out, but broke it off in the process. So I had to drill out the part of the screw that remained, and then used a substitute screw (8-32x1/2) on re-assembly. Re-assembly went easy--note that the removal of electrical connection is a "pinch-squeeze" to pull off.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Gas stove worked, as well as brolier, but oven did not turn on at all. Replacing the bake igniter part did the trick. It is a simple operation, 30 minutes tops normally. In my case the screw was originally installed a little crooked and had caused it to strip and wouldn't come out. As a result, I had to also remove the gas pipe that the igniter was attached to in order to forcibly remove the screw and detach the old bake igniter. This is what caused the extra time and difficulty.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Pulled the range out, unplugged it, removed upper back panel, inserted lens through front of control panel, slid the notch on the actual light onto the lip on the back of the plastic lens. Done!

I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.

After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!

I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.

I removed the two back screws, slid out the old panel, then fitted in the new panel (it fit perfectly) and replaced the screws. Five minutes, tops.

Ordered new knobs. Not an exact match to color but so close only we can tell.