FGGS3045KBB Frigidaire Range - Instructions

pulled bottom door out as far as you can. lift out broiler tray and the tray under that. to get the door completely out. on each side of the rail holding the door from come out push in the tap on each side and pull the door all the way out and off. reach inside and take out two nuts holding the old igniter and cut the two wires and remove it
stripe about 1/4 in of the wire. attache the wire from the new igniter. hold them two and use the white cap and twist it on the two wires and do the same to the other two wires. Bolt the igniter back on with the two bolts and your done. When you turn on the oven the igniter will click and turn on. it will be alot brighter then the old one and the oven will start pretty fast.

I replaced both gas valve and igniter. I removed oven door and bottom of oven for easy access to both. The door slid off easy and the bottom was held by two thumb screws. I removed the gas flare for easy access to igniter & valve. I then removed the igniter & valve using nutdriver, phillips screwdriver and adj wrench. I then followed simple instructions supplied for wire connect on igniter and valve. It was a very easy job for a 25 yr old stove. I made the mistake of ordering only the valve and ordered the igniter later. Having both new parts causes the oven to light in about 30 seconds. Im glad I found partselect online. Nh, westerville, oh

Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean in there MUCH better.

followed online instructions

I simply searched YouTube for the problem I was having and foud it was probably caused by a bad part. I found the part online and ordered it. It was as simple as a few screws and a couple wire-nuts to install. My girlfrind was very happy to get the oven fixed !!!!
Thanks parts-select for having pictures and dimensions so I was sure I had ordered the exact right part.
I was soooo happy to have found you !

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.

Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. After that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.

Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.

My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..

took drawer out, removed tin covers, found igniter and removed,snipped off parts to put on new igniter ,wirenutted old to new put back together ,we had ignition! all in all pretty easy job! detailed instructions that came with new part were easy to follow and precice

1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.

Followed service sheet. Measured 2.6 amps draw at igniter wire which should have been 3.2 amps. Replaced igniter and problem resolved.

Removed 2 screws to oven bottom
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal

Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together

Took the two nuts off that hold the igniter and cut the wires as per directions and used the wire nuts to put them together after I installed the igniter.was a piece of cake and didn't take 15 minutes to do.Oven works great.