FLF337EUM Frigidaire Range - Instructions

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, you can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

first unplug oven. then remove upper back panel(6 screws)with a 1/4 nut driver. next unplug electical connector from control unit. then remove unit by removing (4 screws on corners of unit with 1/4 nut driver. replace unit with new one and reassemble in reverse order.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.

Removed the old oven racks and put in the new ones.

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

Very simple repair. I received my part a few days after placing order; then installed it myself. Anyone can do this simple easy repair.

I thought it was the temperature sensor. I was wrong it was the e. O. C. It wasn't that hard to change,just alot of small screws. Once I plugged it in I tryed to turn on the oven it turned on right away. Only thing is I wish the part was cheaper & also there should have been a white cover on it. Not peel off the old one and re-use it???? The oven is only 2yr's old, but never the less it got fixed. . . Works fine now.

simple to unscrew the door handle from the inside, remove the broken trim, place new trim on, clamp the door together, then screw the handle back on. Went well!

I actually had to buy two parts, the cover and the control panel. But unfortunately I could not get them from the same place. But I replaced the control panel and the cover in about 15 minutes. No issues. Everytihg lokks brand new and works like a new stove. So I am very pleased.

I replaced the oven control board. I used the old overlay because I could not find a model # but I was able to locate the exact replacement part. it took some to find, but it paided off.Thanks for your help. I Got the replacement part # from the old control board.