FGFB79GSE Frigidaire Range - Instructions

Really easy to replace handle. However, because the new handle does not have the metal inserts to receive the attaching screws (!appearently a bit cheaper to make!), I am concerned that it will not last as long. I could find no reference to new attaching screws so used the old ones...hope it works!

Pulled the range out, unplugged it, removed upper back panel, inserted lens through front of control panel, slid the notch on the actual light onto the lip on the back of the plastic lens. Done!

Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

It was easy once I got screws that work.Old screws and handle had machine screws that held handle on.Order screws with handle so you can install immediately...

It was as easy as removing some screws from the back of the oven and replacing the part. I was worried about not ordering the overlay, since it was mentioned in all the descriptions, but soon found it is exactally what i thought it was, the face of the clock and the buttons that you see on the oven. The one I had was still in good condition and i opted to not replace. I just unpealed the old overlay from the old part, stuck it to the new part and it was good. Make sure you unplug the oven before you start to do anything as these electrical components can easily shock and cause harm!

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

I followed the you tube www.partselect.com. Got door off--easy, and other parts off--easy, as you tube shows--I used the adj wrench to remove old screws--there are two--front one off--easy, the rear one was stripped at factory installation--so got it out, but broke it off in the process. So I had to drill out the part of the screw that remained, and then used a substitute screw (8-32x1/2) on re-assembly. Re-assembly went easy--note that the removal of electrical connection is a "pinch-squeeze" to pull off.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

The Conversion Kit was throughall with extra fittings and good instructions. My problem was haveing to pay a lisence gas installer $65.00 an hour to do a safety & pressure test. Maybee future Conversion kits would include a cheap disposable pressure tester with hose, then it would be a complete done job by the owner.

Delivery was fast. Two screws to remove the old oven panel. Slipped in the new panel and tightened the screws with my fingers. Job completed. It was as easy as that.