FGF348KSA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Blanca from Union City, NJ
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced theoriginal power cord.
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miriam from BROOKLYN, NY
- Parts Used:
- 316278700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screws were damaged
Took out old screws and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from San Juan Capistrano, CA
- Parts Used:
- 5304518661
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The range clock wasn't keeping time, and the oven would shut off randomly in the middle of baking.
Removed the metal cover on the back of the range by unscrewing the square-drive screws around the perimeter, left the center screw until the end to make it easier to hold for removal.
The control unit was held in with 4 Philips head screws, and connected by a single wire-to-board connector. Unplugged the connector and removed the screws and the control unit came right out.
The replacement unit doesn't come with a face plate, so I used a razor blade to carefully remove it from my old unit. The adhesive that held it on was still sticky so I was able to easily attach it to the new unit.
Then I just put everything back together in reverse order. One of the easiest appliance prepares I've done.
The control unit was held in with 4 Philips head screws, and connected by a single wire-to-board connector. Unplugged the connector and removed the screws and the control unit came right out.
The replacement unit doesn't come with a face plate, so I used a razor blade to carefully remove it from my old unit. The adhesive that held it on was still sticky so I was able to easily attach it to the new unit.
Then I just put everything back together in reverse order. One of the easiest appliance prepares I've done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pekin, IL
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would Not lite
Watched a half dozen You Tube Videos before I saw the Exact one-Submitted by a Woman-Super Easy-Had the Exact Part from this site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from WEST ROXBURY, MA
- Parts Used:
- 5304509706
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Gas oven stopped working. I read that it probably was the igniter. Bought a new one to ins
YouTube video I used was for a newer version of the same model stove. Door did not have latches to remove it. It was fairly easy getting to the old igniter but a bit of a struggle getting to unplug it, as the connector was behind a small metal shield in the bottom left corner of the oven. Because I couldn’t remove the oven door, it made it more difficult to undo the screw holding it in. I finally did, and from that point it went smoothly. I was worried that I was going to access it from the back, but I didn’t need to. I installed the new one, turned gas back on, moved the stove back to position, and turned on the oven. Very happy to have succeeded, adding a few more years to the stove and saving money for the installation of the igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marcus from hot springs, AR
- Parts Used:
- 5304518661
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Igniter did not light.
The electric was the next step it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wondell from Winnemucca, NV
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not get up or stay up to selected temperature
Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from NORTH PORT, FL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
no heat in oven
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from Daleville, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat from bottom or top element,k stove top and clock all worked fine.
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hiram, OH
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't work
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hemet, CA
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
really bad ugly streaks inside of glass
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from reynoldsville, PA
- Parts Used:
- 5304518661
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
electronic temp controller went bad
first unplug oven. then remove upper back panel(6 screws)with a 1/4 nut driver. next unplug electical connector from control unit. then remove unit by removing (4 screws on corners of unit with 1/4 nut driver. replace unit with new one and reassemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Greenville, TX
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket In Door Replaced
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Reno, NV
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
unscrewed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!