FFEF3043LSB Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerrold from San Marcos, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
switch not always turn off
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from KENNETT SQ, PA
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven wasn't heating properly for a few months and then stopped altogether
The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from MORGANTOWN, WV
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
2 elements stopped working.
My husband followed the video instructions and it was easy to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Anna, TX
- Parts Used:
- 5304518660
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When bake button was pressed the oven did not work
Unscrewed upper back panel of stove. Connected wires from old part to new part one at a time. Then unscrewed old part from stove. After that I screwed the new part to the stove. Replaced upper back panel. Finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WARRENTON, MO
- Parts Used:
- 318178110
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
old element coil burned apart breaking the circuit.
removed the old burner and put the new one in it's place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Andrews, SC
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
switch had a diffirent lug configuration
made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garland Futrell from CHESAPEAKE, VA
- Parts Used:
- 5304503232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken ; oven door inner glass
Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.
Was this instruction helpful to you?
Thank you for voting!
Glides broke on lower storage drawer
The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHERYL from PERRYVILLE, AR
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gasket missing
I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melinda from Three Rivers, MA
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Rusted leveling foot
I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manning from Medley, FL
- Parts Used:
- 5304518660
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
oven not heating display light out
first i remove cover, then i unscrew defective part, remove wires. i then install new part & replace marked wires . I then replace cover, turn on oven and holla! my oven is working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Murfreesboro, TN
- Parts Used:
- 5304518660
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Both heating elements stopped heating at the same time
Discovered that that oven control panel was to blame for both heating elements to stop working at the same time. Went online and ordered the part which was delivered in 2 days. Installation very basic and included the following: 1)Pulled out stove and un-plugged stove 2)Removed top rear panel 3) Removed 4 screws of the damaged control panel (leaving all wires plugged in) 4)Installed new control panel and connected wires one by one to make sure done correctly 5) Replaced rear panel plugged in stove testing oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from SACRAMENTO, CA
- Parts Used:
- 5304518660
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The oven and broiler element would not heat.
The elements tested good. Figured it was the electronic clock timer/control using the sites repair guidance and ordered the part. The remove and replace was very easy. Pulled the stove out, removed back panel and removal and replacement of the part is pretty basic. Be sure and unplug the appliance first. Everything works fine now.
Was this instruction helpful to you?
Thank you for voting!
Switch and Burner went out.
Replaced switch by according to video with no issues, Terminals were nearly identical as the new switch.
The terminals on the new burner were not located in the same position as the terminals on the old burner. I had to reference the wiring diagram to locate the correct wire to terminal location. There was not enough slack in the wires to position the new burner in the same position as the old burner. I had to rotate the new burner so the wires would reach. This cause me to have to rotate the warming burner because rotating the new burner, the terminals interfered with the terminals on the warming burner. I also had to reposition some of the wires so they would not contact the burner and terminals.
The terminals on the new burner were not located in the same position as the terminals on the old burner. I had to reference the wiring diagram to locate the correct wire to terminal location. There was not enough slack in the wires to position the new burner in the same position as the old burner. I had to rotate the new burner so the wires would reach. This cause me to have to rotate the warming burner because rotating the new burner, the terminals interfered with the terminals on the warming burner. I also had to reposition some of the wires so they would not contact the burner and terminals.
Was this instruction helpful to you?
Thank you for voting!