FFGF3019LWA Frigidaire Range - Instructions

Watched a half dozen You Tube Videos before I saw the Exact one-Submitted by a Woman-Super Easy-Had the Exact Part from this site!

removed 2 screws from inside oven door swap out old to new handle reinstall 2 screws done less than 15 min.

The electric was the next step it worked.

replaced it

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

1. Remove the old Trim by opening the door and unscrewing the two top screws holding the trim and glass to the door. 2. Lift the trim piece off of the glass, being careful as the glass will be a bit loose, and unscrew the handle from the trim piece, discard those two screws. 3. Place the new trim piece on the glass so that it fits snugly. 4. Place the screws back through the holes on the inside of the door, through the new trim piece and attach them to the handle. 5. Tighten down snugly and close door. You are done!

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Removed the old oven racks and put in the new ones.

Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

I checked the internet and found PartSelect.com the most affordable (lowest price) for the part. I got the part within 3 days which was very quick. Replacing was unscrew and re-screw at two points. it took me about 15 minutes (including opening the box and talking to my wife on the phone for 5 minutes).

I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)

Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.

We turned off the gas, moved the stove out from the wall and unplugged it. Then we removed the metal back (using an adjustable wrench because we didn't have a square headed screwdriver.) We then removed the four screws that had held the clock/timer in place before the plastic shattered. We inserted the new part and reinserted the screws. Then we replaced the back cover. When we plugged the range back in and set the clock everything worked beautifully.

first unplug oven. then remove upper back panel(6 screws)with a 1/4 nut driver. next unplug electical connector from control unit. then remove unit by removing (4 screws on corners of unit with 1/4 nut driver. replace unit with new one and reassemble in reverse order.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.