FEFLZ87GCC Frigidaire Range - Instructions

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

I unplugged the Stove/Oven electrical cord from the wall, then removed the oven door by unlocking the door brackets with a flat head screw driver then closing the door to the last position before it closes and removing the door from the stove (found instructions on YouTube - very easy, which is optional), then removed the oven racks. Removing the door made it a lot easier to access the broil element and element support bracket screws using a socket wrench. I removed the screws from the rear cover on the back of the stove with a socket wrench to access and disconnect the broil element wires with my hand (pliers if needed). I removed the old broil element and inserted and reconnected the new broil element wires, then re-installed the rear cover. I tightened the broil element in place then re-installed the element support bracket and screws, replaced the oven racks, re-installed the oven door and plugged the stove into the wall. This took about twenty minutes and the broil element is working fine.

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

If you do not intend to take apart the oven door to clean the interior glass, I would recommend you use a clamp to hold the handle and oven door tightly together while you replace the screw. There is a spacer between the back and front panels which could otherwise be shifted out of position. I used a screw extractor to remove the damaged screw and then installed the replacement. Wish all appliance repairs were this easy!

Easy as 1-2-3

Ensured breaker was off. My range is hot wired. Removed all cables from old terminal block with nutdriver. Used phillips head screw driver to remove old terminal block from back of range. replaced old terminal block with new one. Re-attached accessory cables to small terminals first, then the main cables to the terminal block using where necessary long nose pliers. It is important to make note of which cables are attached to each terminal of the block, so make a sketch PRIOR to removal. Also be careful how the cables are attached to the block. You are using 10 gauge cable with thick insulation. It is important that when pushing the range back into position the cable does not put too much pressure on the block as it will break it. That's exactly what happened to this last one. It probably cracked under the strain of the pressure of the cable and finally current running through it weakened it to the point where it broke off from the block causing it to short and trip the breaker.

Ordering the part was easy.

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

I removed two screws and lifted out the ruined bottom. I set the new bottom in, but could not get the screws lined up so left them out. The bottom is heavy enough, it is not going anywhere. I am very grateful the part was available.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

It cannot be cleaned as it welded itself to oven bottom. Two screws in back of oven bottom and it lifted right out. The new bottom says "do not use aluminum foil" Very easy repair.