FFEF3013LWD Frigidaire Range - Instructions

real easy with no problems, thank you

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Ensured breaker was off. My range is hot wired. Removed all cables from old terminal block with nutdriver. Used phillips head screw driver to remove old terminal block from back of range. replaced old terminal block with new one. Re-attached accessory cables to small terminals first, then the main cables to the terminal block using where necessary long nose pliers. It is important to make note of which cables are attached to each terminal of the block, so make a sketch PRIOR to removal. Also be careful how the cables are attached to the block. You are using 10 gauge cable with thick insulation. It is important that when pushing the range back into position the cable does not put too much pressure on the block as it will break it. That's exactly what happened to this last one. It probably cracked under the strain of the pressure of the cable and finally current running through it weakened it to the point where it broke off from the block causing it to short and trip the breaker.

A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.

removed six nutdriver screws and removed rear cover. the only problem i had was the new switch they sent was a little larger then the orig.had to figure out the wires. fit good and works perfect.

After confirming that the renter had broken the timer through frustration I ordered the correct part and fixed the problem.After removing the rear panel it was obvious the timer was broken..just put wires where needed and reinstalled the new clock timer..The oven worked like new..

We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

I thought I was going to have to purchase a new stove which I could not afford, repair man would have cost over $300 to repair. I went on this wedsite, matched the part number with my stove, spoke with customer service, (very good experience), ordered parts, received in approximately 2 days,watched a brief (2 minute)video that came with my confirmation email and TA DAH.....fixed for 1/3 of the repairmems price and so easy. Thanks so much Partselect. Diane

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Took off back of oven, detached old clock piece, attached new one, put back panel back, done.

Statistics said it was the element. I replaced that this did not correct problem. Went with the second statistic and it was correct. I showed the video to my tenant and he replaced it and called me in a few minutes saying it worked fine. Look at the video then it will be easy for you. The only thing in the video that was not clear is that you have to peel the sticker off of the front of the old clock and attach it to the new one. Everything else is exactly like it says.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.