FEFB79GCC Frigidaire Range - Instructions

I read other experiences on line and determined that it was either the element of the control switch. So I decided to order the control. When deciding I had removed the upper back sheild and put it back on. Subsequently a couple of days later there were popping noises culminating in a flash and the stove went 'dark'. I figured that I had pinched a wire when I put the upper shield back on. I removed the shield and looked for black 'short' marks. None were visible. I went to the electric panel and tried to reset the 60 amp breaker. It wouldn't reset and momentarily the lights dimmed. Uh-oh! Went back to stove and opened area where the cord connects to the stove. Direct short- a lose terminal block bolt had welded itself to the chassis! I redid all connections and lined inside of stove back with duct tape- also redid the connections with bolts, nuts and lockwashers covered each with electrical tape. Now reconnecting electric I put the new switch in. Removed the knob from the front and started to transfer the wires from the back. This was a little confusing because the control I received looked different from the one in the stove. After some checking I looked closely at the terminals on each control and they had tiny number/letters on them like H1, Li, H2 etc. So I just transferred H1 0n one cntrol switch to H1 on the new switch- L1 to L1 and so on. Put it all back together, turned on power and everything is working great.

I had order a replacement baking element to start, without trouble shooting the problem. When I had replaced the new bake element, set the oven to bake @ 350*F & watch for the baking element to heat up,it did not heat up. I waited for the oven to cool down,pulled the unit out & unpluged it from the receptacle.I removed the back cover,then I used my volt/ohm meter to check for contunity from the switch to both side of the element. Measured the ohms of the 3 bake elements,all good. Verfied that diodes were ok & there was no open resistors on the circuit board.No proble found. Put the back cover on, pluged the unit into the electrical outlet, pushed the unit back in placed, set the oven to bake @ 350*F, problem solved. My wife have bake several cakes & I cooked Sunday dinner using the oven. The real problem may have been an open circuit between the bottom bake elament & the switch. The repair was completed on 12/02/2012.

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.

Initially we realized there was a problem while cooking with the large eyes and we began hearing an electrical short behind the control switch. I unplugged the power from the oven/cooktop and removed the back panel where I could visually see soot on the switches where it was shorted. Careful while choosing your part from the diagram on Partselect.com. For the model FEF336ECJ, atleast for my oven, the eye switches were reversed and I ordered the small eye's switches! Luckily they have an outstanding customer support and immediately mailed out the new parts and a label to send the wrong parts back. Changing the parts out was very simple. Pull the oven out and UNPLUG IT from any electrical outlet. Remove the back panel. Double check from the label on the front of the control panel that you are working with the correct switch, and before removing the current switch, remove the wires one by one and place them on the new part to make sure you don't misplace these wires. Once the wires are connected to the new part, pull the plastic knob off of the old switch to reveal the screws on front of the panel. Place the new switch where the old one came from and fasten the screws back in place. Replace the knob, replace the back panel(for safety) and test the new switch before you push the oven back into place. If you can turn a screw driver, move the oven, and unplug the power, this easy do it yourself repair will save you possibly hundreds by not calling a repair/handyman who would absolutely love you to pay out the nose for such an easy task.

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!