FEF303HWB Frigidaire Range - Instructions

I did as instructed on your video of how to install the terminal block, btw GREAT VIDEO!!
I'm a 66 year old female and if I can do it, anyone can.

Thanks, PartSelect

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

First I gave my roommate (an engineer) a screwdriver to remove the two screws that held the element in place. Then before I could hit the switch for the circuit breaker, he nearly fried himself by trying to take out the element! He gave up helping me after that.

Then I turned off the circuit, pulled the oven out and unplugged it, removed the racks from the oven, removed the two screws that hold in the element, and lifted up each side of the element and pulled each piece out. Unfortunately, they were a little stuck in back.

So I pulled out the oven, unscrewed the 6 or 8 screws that held up the back panel, and pulled the back panel off. I disconnected the two wires clipped to the element and pulled the old element out by lifting up and pulling them out. I then put in the new bake element, clipped the wires back on, put the oven's back panel on and screwed it in place, and then screwed the bake element back in with those two screws. Easy - a

turn off power to oven at breaker box
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on

My part was the oven burner for my Tappan stove. I followed a very helpful you tube video. All I had to do was use 1/4" screw-type screwdriver (not sure what you call it), remove screw, pull out each side, pull part away from wire; and then insert the new oven burner!! SIMPLE and I'm a 68-year old widow! I was proud.

Using small square tip screwdriver (#1 if my memory is correct), removed two screws at rear of oven pulled old element carefully by pulling, removed wire from each side, attached wires to new element, slid to back feeding wire back where they had been, put screws back in, tightened and viola, stove working great. Approximate time to do job, less than ten minutes!

Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.

Cut the old block off tied new wires to hot wires . That easy!

I removed the 2 screws, making sure not to drop the wires attached. Took off old wires ,then put new wires on new element, screwed it back into place and it was working. sooooo easy!!

Pulled out old burner/inserted new

replaced the element.

Easy as removing 2 screws, pulling the wires through the back wall of the oven so I could connect the new element and replacing everything. Honestly, it only took around 8 minutes.