FEF354GBC Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Louis from GAINESVILLE, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bottom oven element non-functional
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal procedures. Also good time to clean oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELKHORN, WI
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
run away temp
I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.
I will have to toss out this stove and buy new as you and no else has this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlene from ERIE, IL
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner not heating up.
Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from FRUITHURST, AL
- Parts Used:
- 316436000
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from PERRY, ME
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bad element
Remove screws pull off wires and install new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from ASHEVILLE, NC
- Parts Used:
- 318372210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heating element for a frigidaire stove top broke
Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.
Great company. Makes it easy for me order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from MARIETTA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was over heating temp. of oven keep climbing
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from KEENE, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not controlable
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from CINCINNATI, OH
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel rusted away
Removed two screws removed and replaced panel.
Was this instruction helpful to you?
Thank you for voting!
The6" surface element I use the most broke. I then decided it was time to buy original replacement drop bowls, since the ones I had been buying never it correctly.
Actually, a child of average intelligence can do this. Just pull the surface elements, take the old drip bowls, install the new ones and re-install the surface elements, including the brand new one I received.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MAINEVILLE, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element went out
Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremiah from Crawfordsville, IA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The baking element developed hot spots and stoped working.
I removed the baking racks then unscrewed the default screws for the baking element.I then disconnected the electrical leads from the damaged element. I then removed the old damaged baking element and installed the new baking element, attaching the electrical leads after cheking for weak spots in the element. I then re installed the baking racks and started the oven to burn off any factory oils on the baking element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Palm City, FL
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Range displayed error code F10
Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.
Was this instruction helpful to you?
Thank you for voting!