CGGF3054KBC Frigidaire Range - Instructions

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

The top of the door trim broke causing the side and glass to be loose. Easy fix by removing the broken trim and installing the new one.

Approximately 2 minutes to replace.

Oven ignitor is on the bottom gas unit. Ignitor is in oven and plug is in warmer oven on left wall at very back of warmer oven. It has duel function to light both upper and lower gas burners (in oven). Wires of new plug that I received were shorter than existing wires and would not reach the plug from ignitors center mount location to plug at far back of warming unit on left wall. Even if the wires would have been long enough, I couldn't figure out how to "release" the existing plug. Easy solution: Cut old wires at junction of old ignitor (leaving wires as long as possible). Cut new wired as close to new male plug as possible (leaving wires as long as possible on new ignitor). Strip ends of old and new wires and wire nut with porcelin wire nuts (hardest part of job was locating porcelin wire nuts)! After placing wires out of the way of burner and ignitor, reassemble stove parts. AVOID touching new element as oil from hands will decrease the life of the element. Good Luck..

Tore the oven apart and replaced the igniter, then put the oven back together. Perhaps if Frigidaire manufactured an appliance that lasted longer than three years this wouldn't have been necessary. This is the second Frigidaire range that only lasted three years. Believe, the next stove we buy will definitely not be a Fridgidaire!

I "You Tubed" disassembly and commenced by disconnecting electric power. Removed door via You Tube instruction, removed back panels of unit, and replaced the oven temp probe. Easy Peasy. Then removed bottom of oven, next level above the burner and started to remove the igniter. One nut refused to be removed so I removed the burner and cut the nut and drilled it out. I reinstalled the new igniter with a metal screw from the rear panel and reinstalled the burner. Through the tiny hatchway I reconnected the new igniter and reassembled the oven to test. Just fine heated to 350 in 7 minutes. Awesome. Then, I called my brother, Pat, to give his imprimatur to the hillbilly nut switch. He said ok, I am done.

To any reading this, I would order the igniter and the burner at the same time. That tough nut cost my one extra hour.

I ordered the replacement igniter for the oven portion of the unit from Part select. It shipped very quickly. Upon receiving the igniter it was time to get to work. It took roughly 10 mins to replace and we were back up and running.

Twisted replacement bulb into place easily. Let there be light!

Unplug oven to prevent shore. Make sure to purchase ceramic wire nuts to complete repair. No access to able to plug in the plug. Need to unscrew the plates in the bottom of the oven to get to the igniter. Cut the plugs off and use the ceramic wire nuts to connect the wires. Put make together. It took a Month for the part to arrive.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

took the two screws out by hand, slipped out the ruined panel, slid the new one in place, replaced the two screws...simple as that

Removed the grate and replaced with griddle. By using a replacement part rather than buying stove with the griddle, I saved $80. Didn't realize the model I bought didn't have the griddle included even thought it was displayed with one.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

The installation of the bake burner tube went well. I followed the instructions within the Video as it pertains to replacing the Bake igniter. That video also describes the removal and replacement of the bake burner tube. The original screws that mounted the igniter to the burner tube bracket were damaged. I replaced them with 18-8 Stainless Steel Serrated-Flange Hex Head Screws, 8-32 Thread Size, 3/8" long. As noted in the video, the oven bottom panel is removed using a flat head screwdriver. For all other screws I used a 1/4" socket and ratchet. A Nut Driver would have also worked just as well. On initial start-up after the repair there was a minor light odor from the flame coming into contact with the new metal burner tube that dissipated within a few moments. In all everything went very well.