CGEF3055KBC Frigidaire Range - Instructions

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!

ordered control board from PARTSELECT if you need it fast over night it remove rear of back guard with NUTDRIVER 4 phylips screws hold the control board in place it helps if you have a phone to take pictures to see where the wires go when you connect them to the new board the overlay is not to hard you have to make sure to start at one end and get the end lined up use your fingers to feel the edge of the control board at one end put overlay in place and gently lay it in place and start laying it down slowly making sure it is going strieght once your at the other end and its down i used a soft cloth to press it down across the face and happy to say the syove is working once again

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

I was actually replacing an EOC and it did not state anywhere that I might need this. In the end I did, the new board is not compatible with the old overlay and I had no idea so intended to re-use the old one. I had to wait for the new one and it worked fine. The EOC had actually been damaged by a power surge and it was obvious it was bad. I was actually hoping that this would resolve a temperature drift issue but it did not.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

After settling that it was the Surface Element Switch, ordering and securing the switch, the first step was to disconnect the power to the Oven/Range. Next pull out the Range and remove the back and disconnect the switch from the top of the Range. Using the new switch I removed the wire connectors from the old switch and reconnected them to the new switch in the same spot that they came from. After connections were secure I reattached the switch to the back of the Range and reattached the back of the Range. When everything was back in place the power source was reconnected and that was it.

I watch you tube of how to repair to gain my confidence and attempted the project. It was fairly easy. I took photos of wires so I wouldn’t make any mistakes. Boom ! Finished and works like a charm!!

I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.

However the 1a 1b etc. Are very hard to see thus the need to magnify. Then it was easy.
I must say the guy I talked to was very nice.

Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)

Watched You Tube 3 times. Removed the stove back covers top and bottom.
Ordered the new electronic control board and overlay.
Took picture of existing control board and connections.
Viewed parts select online schematic of the stove, make and model.
Ordered the new black overlay, did not want to take time to try to save old black overly.
Parts arrived.
Re-watched You Tube.
Installed the new electronic control board and included electronic filter as per You Tube.
Tested the oven.
Works like new.
Saved $ 200 to $ 300.
Great fun.
Hero to my wife !