CPLEFZ98GCC Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tracy from Summerville, SC
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My five-year-old Frigidaire Gas stove was giving an F 10 code.
I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from S CHESTERFLD, VA
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat
Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Palm City, FL
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Range displayed error code F10
Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from MARIETTA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was over heating temp. of oven keep climbing
removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELKHORN, WI
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
run away temp
I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.
I will have to toss out this stove and buy new as you and no else has this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phin from HARRISBURG, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.
My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRACY from NEW PHILA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not heat or sometimes hold heat to set temp
I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.
Many thanks to PartSelect for their comprehensive website and fine service.
Many thanks to PartSelect for their comprehensive website and fine service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BELLEVUE, WA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Element burned out
The original instructions were to replace burner and plug wires back in the same plug they came from.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from OWASSO, OK
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven temperature was not consistent.
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from AUGUSTA, ME
- Parts Used:
- 316430900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Element burned out
Turned off power at breaker, took back off range, removed red and blue wires, removed oven door, removed two screws holding in broil element, removed wires supporting old element, installed new element and reversed procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from EDGEWATER, FL
- Parts Used:
- 5304498754
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The panel had rust spots.
I removed the door from the stove and started to remove the screws that were holding the panel to the inner panel. Replaced with the new panel and put it back together.
Was this instruction helpful to you?
Thank you for voting!