CFEF3005LWC Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- PERRY from LECANTO, FL
- Parts Used:
- 316436000
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
new switch was not wired like old one
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Danville, IN
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Element burnt out
The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Union City, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Element caught fire when i preheated my oven
I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Ashton, IA
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
burner wouldnt heat
removed element , cut wires, conected wires,replaced element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Chicago, IL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Racks needed to be replaced.
Slide out the old; slide in the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Lovelady, TX
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner wouldn't stay hot.
I pulled out the old element and the new one just plugged right in.
Was this instruction helpful to you?
Thank you for voting!
Replacement bowels didn’t fit
Pulled the heating elements out took the bowels out that didn’t fit, threw them away and replaced them with the perfectly fitting bowels from this site and replaced the heating elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Portage "BlueKnob", PA
- Parts Used:
- 316048414, 316048413, 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wiring was burnt off to burner
The range, (1988 Tappan) was givin to the church by one of our members. While using it, --after a period of time-- the wire burnt off to one of the burners. Since the couple gave us a brand new top for the stove that was still in the box, we decided to fix the stove up.
Now, with new wiring to all four burners, new shiney drip pans and,,,,a new top, we have a very new looking stove for in our church kitchen.
The parts I ordered from PartsSelect, came in just a few days of placing the order,
This is one site that I have wrote down in my address book for any future parts to items we may need.
Now, with new wiring to all four burners, new shiney drip pans and,,,,a new top, we have a very new looking stove for in our church kitchen.
The parts I ordered from PartsSelect, came in just a few days of placing the order,
This is one site that I have wrote down in my address book for any future parts to items we may need.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chhabildas from Charlotte, NC
- Parts Used:
- 318372210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Enement was blew out.
I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.
Was this instruction helpful to you?
Thank you for voting!
Electrical connection pulled off the element
When I pulled the element out of the back panel of the oven to remove it, the electrical connection got caught on the edge of the hole in the panel and disappeared back into the oven insulation. It was difficult to find and pull it back out to reinstall it on the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Westfield, MA
- Parts Used:
- 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement burner
Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Armando G from Alice, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Electric burner switch shorted out.
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Elberon, IA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large burner wouldn't heat
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Gaffney, SC
- Parts Used:
- 316203200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bottom elerment burnt into
First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.
Was this instruction helpful to you?
Thank you for voting!