FES367DCB Frigidaire Range - Instructions

Turned of breaker to stove. Removed knobs. Removed four plastic nuts under knobs. Removed five screws that hold swith plate in place. Removed two screws that held actual switch in place. Swaped one wire at a time to new switches. (Switch was a newer model so seeing switch markings was critical to correct wire replacement!) Installed in reverse order. All in all. The job was easy and the new swith looks to be of a higher quality. This ia a gee-wiz--when the old switch failed it failed to the full on position. I had a pot of chicken slowly simering on Lo went to the garage to work a project came back in to a house filled w smoke/alarms going off and the burner on full high-glowing! The old switch was dangerous!

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.

I mistakenly took the two screws out of the front piece above the oven. Except for that the time would have been maybe 10 minutes. The knobs all four came off easy and so did the retainer nuts and the six screws holding the metal plate. I took the old switch out after turning off the power. I had the new switch in one hand and removed one wire at a time from the old and put it on the new one. Put the parts back in place and turned the power on and turned the switch on. Works great! Saved about one hundred and thirty dollars from what the repair service charged last time.

The repair went relatively easy. I even cleaned all the layers of parts when they were removed from the glass panel. I have to thank the excellent customer service and super fast delivery. Overall a quite easy task and $$ saving as well!

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

watched a U-Tube video on this subject.....worked like aa charm!!

After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!