KF420GDF2 Frigidaire Range - Instructions

I just had to plug the new burner plate in the receptical
and it works again very well.

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

Removed the 2 element holding screws, disconnected the element leads & remover element. Replaced with new element.
All in all a real easy job (wish all repairs went this easy)
PartSelect had the element at the house within a couple days (Correct part I might add) which made the wife happy !!

Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device)
Plugged in new one and replaced screws to hold in place.

I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.

Removed 2 rear screws. Pulled out element. Popped out 2 wire clips. Replaced old element with the new one and attached wire clips. A caveman could do it.

Read the reviews and followed the same procedure. Very east..took about 10-15 minutes.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.

My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!

Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.

First, I removed the two screws that hold the element in place. I pulled out the element about 2 inches, and then I wasn't sure what to do, so I called my son and he finished the project in about 5 minutes or less. He pulled off the wires and then put the new element in place, slipped the wires on the new element, then pushed it back into the holes and screwed the screws back in. Worked great.

i removed the stove eye and the old drip pan. then i placed the new drip pan in and replaced the eye. the new drip pans fit way better than the ones that i took off of it.

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.

took two screws out disconnected wires and connected new element ,screw back togather in about ten mins and started cooking dinner