GW30SPED1 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
My burners were shot!
Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from FREDERICKSBRG, VA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner would cutoff intermittently
Pulled out old burner/inserted new
Was this instruction helpful to you?
Thank you for voting!
Rusted Drip Bowls
This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dr. Johanna V. from North Conway, NH
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
Oven element burned out
Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from LANOKA HARBOR, NJ
- Parts Used:
- 318372210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PRAIRIEVILLE, LA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from El Dorado, AR
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bottom element broke and would not heat
the repair itself went smoothly. the clips that the new part connected to were old and slack. the clip came undone and had to pull the stove out to get to part from the back. i squeezed the clip together to make it stay on the new part and it held. the oven is heating well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from OCKLAWAHA, FL
- Parts Used:
- 5303935086
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Can't regulate burners
Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from CHEWELAH, WA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from BROOKFIELD, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
element burned out
pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from Jacksonville, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The old element caught fire.
Unscrew the old one and unplug the wire leads. Then plug in the new one and bolt back up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Simon from New Port Richey, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven heating element
I just removed two screws. Pulled the element out, unhooked the wires. plugged the wires into the new element screwed it in and was done
Was this instruction helpful to you?
Thank you for voting!