RS33BNL1 Frigidaire Range - Instructions

I used this site self diagnostic page and ordered the oven heating element as that was the item suggested for repairs. It was the correct part to fix my oven problem. I had my electrician visiting to install two light fixtures so I had him install the new heating element in the oven. Even with him going to the garage to turn the circuit breaker off for the range the installation took less than 5 minutes.
This site is the greatest!

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.

The only difficultly I had was to bend down the ends of the new element so they were straight. Easily done with a pair of pliers. Slide the connectors from the oven over the ends, and put them back into the holes for them in the oven.Correct size socket and it was installed in minutes. I turned the oven on, and there was my heat. I used an oven thermometer to check the heat, and it was perfect. Quick service and the element was exactly the correct size.

Took the back off, and took the terminals off. Took out the old element and put the new one in and put the terminals on and screwed it back in and put the back on. And all done.

juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.

took two screws out disconnected wires and connected new element ,screw back togather in about ten mins and started cooking dinner

Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.

After the oven cooled, removed the bake element withe a couple of screws, got on line and ordered the part. Two days later the new element arrived and we put the screws back in with the new element. Problem solved.

unscrewed rear connections, removed broken element, installed new

I'm a stay at home mom so when the oven didn't heat up I through oh no I have to get a new one. Well who can afford to get a new oven right after christmas. So I played with it to see if the other parts still worked, when I found that they did, I googled the the Appliance name, that is when PartSelect showed up and they had a video on how to replace the bake element. It looked doable so I ordered the part and it really was a easy fix. It took less than 10min all I had to do was pull out the old element and put in the new element. Only trouble I had was, I had to bend the prongs alittle but that was no problem. Thankyou PartSelect

We tested all of the other "functions" of the oven to make sure that everything else worked fine, and we realized that the problem really had to be the element.

We ordered it and it came within 72 hours! We simply unscrewed the faulty element, made sure that the wires were handled carefully (circuit turned off!), and inserted the new element and rewired and screwed back into place the screws that were removed.

Simple as pie! You can do this! You don't need a service call for this one guys! Get BRAVE!!

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.

I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.