KF460GDW4 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- steven from EPPING, NH
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The bottom Heating element burned out.
I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Spencer, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" stove top element would not warm up.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Lake Luzerne, NY
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element burned out
I turned off the circuit breaker to the range. Next I removed the two screws that fastened the element to the rear of the oven. Then I pulled the element out far enough to be able to reach the spade clips and disconnected the element. I connected the replacement element to the clips and fastened it to the rear of the oven with the two screws. I turned the circuit braker on and the element functioned properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dr. Johanna V. from North Conway, NH
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
Oven element burned out
Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wyndmoor, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bake element would'n heat
Removed the racks first. Then removed the two screws that held the element in place.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melody from Moberly, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Oven Baking Element Burned Through Causing It to Break Into Two Pieces
First my husband removed the two screws that held the heating element into place. I had tried it with pliers which didn't work well. But with the proper socket the screws came loose easily. He pulled the heating element out a few inches and detached the wires. He then slipped the wire over the new heating element and screwed the new element into place. Now we can bake again. Very easy and we received the part quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Centralia, WA
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element shorted out
Oven is an in the wall unit. Normally it is an unplug and plug in. The old one had a melted connector, so the connector had to be cut off and replaced as well. Be sure to turn off the electricity at the braker to be safe, first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Garrettsville, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element split and quit heating
If I didn't need my oven ASAP, I would not even have attempted to do this repair before my husband came home. But he wasn't going to be home for hours, and I needed it now!
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!
Thanks,
Vicki
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!
Thanks,
Vicki
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from La Crescent, MN
- Parts Used:
- 316442301, 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out baking heating element in oven
Removed element by loosening two screws, disconnected heater element and connected new element and reattached to oven wall. Turn on oven to check for heater to work. Confirmed heater worked. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Castle, PA
- Parts Used:
- 318372211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from El Dorado, AR
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bottom element broke and would not heat
the repair itself went smoothly. the clips that the new part connected to were old and slack. the clip came undone and had to pull the stove out to get to part from the back. i squeezed the clip together to make it stay on the new part and it held. the oven is heating well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from BROOKFIELD, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
element burned out
pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!