REG533MDM3 Frigidaire Range - Instructions

I figured that it could not be a hard repair, that these things "die" in the ordinary lifetime of an oven, so that they would not make it too hard to get to. I pulled out the oven and disconnected it; opened three screws on the back, took off the back plate, and you could easily see the two connectors to the element. They came off with a gentle tug with pliers. Then you open the oven, and remove one screw on each side where the element is connected to the back wall of the oven. A magnetic hex socket end for the screwdriver makes it easier. Remove the old element gently through the glass wool insullation, and insert the new one with the element "legs" down. Verify the placement of the element connections in the back, and then replace the screw that hold the tab on the base of each element side to the back wall of the oven. Then, carefully reconnect the connector sleeve onto each end of the element in the back of the oven snuggly. Close the back panel with the three (the forth on the top was not tight and didn't need openening or closing)screws to the sides and bottom of the panel. Replace oven and reconnect to power, and test the element. It all took less than half an hour.

I unhooked element from wall on inside. Only two screws to undo. I then took back of stove off and unhook speaker like connectors. It was very simple.

Had to drill 2 new holes 1/4 lower in oven so new coil would bolt up evenly besides that it went easily.

I had a friend come..He unpluged the old one and put the new one in when it arrived. All is well. Thank you for having the part that was needed. Now the over works super..
S.Bullock

They don't make appliances this easy to repair anymore. just as others say: screw out, unhook element ..hook new one to wires, screws back in.. you're DONE.. Thanks for great service and very quick delivery

Just removed nuts. Pulled out the element from the unit. Disconnected each end. Reconnected new element. Pushed piece back into insulated unit. Attached nuts. Done.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.

took out the screws at the back of the oven, removed the old element and put the new one in, replaced the screws. The new part was mostly the same size as the old one, some of the angles were different and the ends slightly different, but it fit and works great.

My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!

Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.

First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.