REGS38BKW0 Frigidaire Range - Instructions

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

took me longer to find my 1/4 inch nut runner and drill than to change out the element.........simpliest replacement i've ever encountered and i'm 64 years old. less than 2 minutes......

Even though my exact model was not matched by Parts Select the bake element shown in a picture for a different model was correct. The length the bake element protruded through the wall of the oven was the same as the old one. The element arrived within two days, packaged so it would not be damaged en transit.

The problem was that there was heat in the oven but only a little. This threw me off at first but my wife tells me that the broiler element is used as the oven heats up. So bottom line is, the main element was burned out and once I replaced it, everything worked fine.

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

shut the breaker off , remove the racks' use nut driver to remove the 2 screws, carefully slid the element ends out of the holes, disconnected the wire ends (push on connectors) discarded the old element and replaced with the new in reversed order. very simple

My husband had no problems except the end of the new element was different than the original, but hooked it up ok!

Took door off and remover racks. . Then took a nut driver and took the two screws out pulled element out and unpluged it from the wires. . . Then put the new element in place attached the wires and reinsalled the two screws. . . And I was done. . . Ready to rock and roll. . . . . Thanks to insructions from parts select very easy. . . . Thanksguys. . . . . . Ralph from texas. .

Reviewed a YouTube video. Then removed the old element and installed the new one. It was extremely simple! I became my husband's hero instantly!

I have a wonderful range that I love and it is almost 30 years old! The baking element died...burned and broke in half. This is the second time I have had to replace it (not bad for the old girl) and the first time I used PartSelect. I ordered the part late in the day and it was delivered by FedEx in just under 24 hours....now that's service! This is a very easy repair that anyone can do. Just turn power off to range, unscrew the hexagonal screws, ease out the bad element, reattach electrodes to new one, ease it back into range, put screws back in and you are done. Ten minute job you can do yourself for the cost of the part. Great great service from PartSelect.