REG38BNW1 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from PRAIRIEVILLE, LA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Castle, PA
- Parts Used:
- 318372211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from BROOKFIELD, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
element burned out
pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from La Crescent, MN
- Parts Used:
- 316442301, 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out baking heating element in oven
Removed element by loosening two screws, disconnected heater element and connected new element and reattached to oven wall. Turn on oven to check for heater to work. Confirmed heater worked. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Chadds Ford, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broken Bake Element
followed your directions - excellent
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Dayton, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking element cracked
Removed the baking element with a nutdriver. Slid it to the front of oven and removed the contacts on the back side. Installed the new element and installed the contacts at back of element. Slid it in the holes on back inside of oven and used a nutdriver to install the screws. It was very simple to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Fremont, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cooked things very SLOWLY.
Pulled old burner out, pushed new one in. WHAT A DIFFERENCE!! Heats very quickly, now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Batesville, AR
- Parts Used:
- 318372211
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
An aluminum saucepan had overheated and melted onto the element.
Unplugged the element and the melted on pot. Plugged in the new element. I thought I might need a whole new cooktop but a new element was very easy to find online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Galen from Ulysses, KS
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking Element had fallen into 3 pieces
Repair was simple. Unplugged stove, removed a plate from back of stove. Disconnected wiring. Removed screws from inside oven, removed old element, installed new element. Replaced screws, hooked up wiring, replaced back plate, plugged it in, used it that night.
Thanks for sending the right part the first time and getting it shipped so quickly.
Thanks for sending the right part the first time and getting it shipped so quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry L. from Kendallville, IN
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven wouldn't heat on Bake.
First shut power to oven off, removed the oven door and oven racks. Removed the 2 screws from the back of the oven holding the element in place. Slowley pulled the element out and removed the wires, pulled off with my fingers. Replaced the old with the new in the reverse order. Saving the Wife a pile of money.
Thank You,
Jerry R
Thank You,
Jerry R
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angel from cleveland, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
the bake element was broke in half
first i remove the two screws that hold the element then i pulled the element out few inches out i disconect the two wires and i put the new element back in place 10 or 15 minutes top.really easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from TEMPLE, GA
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating coils stop heating
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- yrna from Farmers Branch, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
heat element would not heat.
Turned off power to oven at breaker box.
Removed one screw that holds the element in place. The other screw would not unscrew, I went to hardware store for drill bit and special hand tool (which cost less than $15) to remove stuck screw. I didn't have the right size screw, so I went back to hardware store for two new screws. Pulled the element out and disconnected the two wires(they are plug-in). Lost one wire into the back of oven because I did not hod it for the new element to plug onto. I removed the back of oven by unscrewing several screws and located the wayward wire. I threaded it back into the hole (easy) and someone grabbed it and held onto it while I screwed the back of the oven back on. Then I placed the wire connectors onto the new element being sure to squeeze hard with pliers so there would not be any slipping off of the wires. The power was restored and the element worked great. A less than 30 minute job took over 2 hours because of inot thaving he right tools.
Removed one screw that holds the element in place. The other screw would not unscrew, I went to hardware store for drill bit and special hand tool (which cost less than $15) to remove stuck screw. I didn't have the right size screw, so I went back to hardware store for two new screws. Pulled the element out and disconnected the two wires(they are plug-in). Lost one wire into the back of oven because I did not hod it for the new element to plug onto. I removed the back of oven by unscrewing several screws and located the wayward wire. I threaded it back into the hole (easy) and someone grabbed it and held onto it while I screwed the back of the oven back on. Then I placed the wire connectors onto the new element being sure to squeeze hard with pliers so there would not be any slipping off of the wires. The power was restored and the element worked great. A less than 30 minute job took over 2 hours because of inot thaving he right tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from MENASHA, WI
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burner elements not heating
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
Was this instruction helpful to you?
Thank you for voting!