RE533DL0 Frigidaire Range - Instructions

took me longer to find my 1/4 inch nut runner and drill than to change out the element.........simpliest replacement i've ever encountered and i'm 64 years old. less than 2 minutes......

Even though my exact model was not matched by Parts Select the bake element shown in a picture for a different model was correct. The length the bake element protruded through the wall of the oven was the same as the old one. The element arrived within two days, packaged so it would not be damaged en transit.

The problem was that there was heat in the oven but only a little. This threw me off at first but my wife tells me that the broiler element is used as the oven heats up. So bottom line is, the main element was burned out and once I replaced it, everything worked fine.

Locating part on web site, ordering, receiving next day & installing was very very easy. Information provided on PART SELECT web site and that provided with part made this a very easy and cost effective repair. With service provided by PART SELECT there is no reason to pay for an expensive service call in addition to what a repair company would charge for the part.

I used this site self diagnostic page and ordered the oven heating element as that was the item suggested for repairs. It was the correct part to fix my oven problem. I had my electrician visiting to install two light fixtures so I had him install the new heating element in the oven. Even with him going to the garage to turn the circuit breaker off for the range the installation took less than 5 minutes.
This site is the greatest!

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

The repair was pretty easy with the help of your on-line diagram. Other than the fact my husband failed to turn off power to the stove. Needless to say he got a small shock by the stove, Once he turned off power it went fast and safe.

Received the order the next day. Unpluged the stove from electricity. Used a 1/4 craftsman wrench to undue the screws. Pulled the old one out and disconnected the conection. Reconnected the new one. Pushed back in place, then re-tightened the screws. Thanks for having it in stock.

Unplugged stove. Removed oven racks. Using 1/4" nut driver I removed two screws from back wall of oven that were holding bake element in place. Pulled stove from wall, removed lower back panel. Disconnected electric saber connectors. Pulled old element from oven. Put new element in oven. Reinstalled the two 1/4" screws. At the back of the stove, I reconnected the two push-on saber connections. Replaced back panel. Pushed stove back in place. Plugged in the power cord. Checked oven. Works fine.Great experience with Parts Select in every way.Total work time: about 20 minutes.

Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.

The PartsSelect site provided the hint that the baking element might be the root cause of low heat. SO I order the part, got it within a few days and installed it. Simple matter of removing a small read cover and tow faston connectors to the heatng element along with two Phillips screws that secured the heating element. Oven now works like new!! Thanks PartsSelect, you saved me a bundle!