FEFB78DSA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from UNIONTOWN, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Switch quit working and wouldn't turn
Take handle off, then back cover. Of course unplug power. Switch wasn't built exactly like the original but all you have to do is connect each wire to the same letter, number code as on the old one . Works like brand new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from SANDY, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
burner switch failure
Unplugged the range. Removed the top section of the back of the stove to expose switches. Removed the knob, (pulls off exposing the 2 switch screws), unscrew & pull out from the back. The new switch was slightly bigger but the same manufacture and post letters & numbers. Transfer wires one-at-a-time from the old to the new switch. Mount the new switch back in place, put the screws in and the knob on. I plugged in the stove for a quick test, HA....works perfectly. Unplugged again and put the back panel back on, plugged back in and pushed the stove back in it's hole. BEFORE; the old switch when turned down would come back on BUT stay on high, a lot of boil overs. FINALLY: when turned on, it would NOT turn off, a real fire hazard. Thank you for having an original replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LAKEWOOD, OH
- Parts Used:
- 316575500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken oven door cap.
Watched a video - piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from W SAND LAKE, NY
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
8" burners were not responding correctly to the switches
Pull range away from the wall. Unplug range. Remove back plate covering the switches. Remove defective switch. Use bent paper clip to press center of terminal connectors and disconnect terminals. Reconnect each terminal of new switch as you go to avoid confusing terminals and connectors. Re-attach switch. Plug in range and test elements. Clean range area. Push range back into place, being sure to engage the anti-tip safety device.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adolfo from new york, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Edina, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large front burner would not come on under setting of "3"
Replaced infinite control very easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from North Mankato, MN
- Parts Used:
- 316436001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Arcing could be heard (and later seen) inside the switch
Switch was easy to replace. Some hex head screws to remove the panel and two screws to remove the switch. Though the plug in positions were totally different, all the quick connect terminals were marked on both switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from KERSEY, PA
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
sparking element
removed back and transferred four wires to new part and replaced back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WATERTOWN, MA
- Parts Used:
- 5303935318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Handle
1. Order part
2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent.
2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Pompano Beach, FL
- Parts Used:
- 316430900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broil Element shorted out
I unplugged the Stove/Oven electrical cord from the wall, then removed the oven door by unlocking the door brackets with a flat head screw driver then closing the door to the last position before it closes and removing the door from the stove (found instructions on YouTube - very easy, which is optional), then removed the oven racks. Removing the door made it a lot easier to access the broil element and element support bracket screws using a socket wrench. I removed the screws from the rear cover on the back of the stove with a socket wrench to access and disconnect the broil element wires with my hand (pliers if needed). I removed the old broil element and inserted and reconnected the new broil element wires, then re-installed the rear cover. I tightened the broil element in place then re-installed the element support bracket and screws, replaced the oven racks, re-installed the oven door and plugged the stove into the wall. This took about twenty minutes and the broil element is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
My oven door seal was worn and did not seat properly. It leaked heat.The infinite burner was not warming in the low heat positions
I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- santa from glassboro, NJ
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temp was not reading right
remove back panel took out old part splice wire replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!