FEF388CJBB Frigidaire Range - Instructions

The how-to video was helpful, though my old range has an extra spacer panel between the glass-top and oven, requiring an extra couple of screws to be removed, with different-sized Philips head.

1. Replacement part was not exactly like the original.
* Inner and outer elements lacked an insulating spacer.
* The two wiring terminals/docks were swapped.
* So had to attend to where the wires were going.
* Worked, just needed some observation & thought.

2. MOUNTING HOLES
a. Old element had clips mounted at holes 9 & 45.
b. Old element had the four-terminal wiring dock attached by screws at 71 & 72 (also where 0 would be), “ahead” of the small three-terminal port by about 5 number positions.
c. Corresponding holes in replacement were not the ones with pre-drilled insulating material. But it's really soft and easily drilled by hand. Probably could have just screwed directly into it.
d. Replacement four-terminal dock is “behind” the smaller one by a few number spots.

3. WIRING IS REVERSED
As noted, the two terminal docks are swapped, so watch the wiring.

Old terminal docks/ports were directly connected by a wire shunt that tied those terminals to the inner ring element.

The new element also has inner/outer burners, with no separation, but we can trace the wiring. Instead of a shunt, the docks are connected via the element. The right port on the small dock is connected to the inside burner, and that inside burner element exits into the large dock. That’s
the inside-burner circuit.

Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal procedures. Also good time to clean oven.

older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

took out the old one, screwed in the new one. very easy.

This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and arc that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.

removed screws,unplugged terminal leads,installed new one,back in business.

First thing I did was turn off power to the range at the circuit breaker. The repair was generally easy with the exception that 1 screw holding the broiler element support was "welded" into the oven ceiling. I stripped the screw trying to get it out. Fortunately, I had a special tool that allows one to grip the outer edge of the screw while turning it --- and that's how I got it apart. Once the broiler element support was off, I removed 2 screws holding the broiler element itself to the oven wall and carefully pulled the broiler element out from the oven wall and detached the wire clips connecting the wires to the broiler element. I reattached the clips onto the new element and installed the new element back into the oven wall. I then reattached the broiler element support using a another screw (because I decimated the original one). I then turned the circuit breaker back on and turned the broiler on. Woila. My broiler works again! Special thanks to the people at this site who were very helpful in seeing to it I got the correct broiler element. The original ordered broiler element was delivered to the wrong address. The folks at this site sent me another one. To make a long story short, they saw to it I got the correct part. I highly recommend this site based on my experience with them.

It's a simple project. Remove old element and replace it with new one. Access is easy. Only one tool needed. What impressed me was how fast the part got here, like the next day after I ordered it.

Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

Remove drawer. Insert new slide. Install drawer.

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.