PLGF659GCA Frigidaire Range - Instructions

The repair was simple - I first needed to test the original igniter with a circuit tester. Once I determined that the part was bad, I simply removed it and replaced it with a new one from Partselect. It was a matter of simply unplugging a few wires and splicing the new igniter in with wirenuts. Fairly simple.

First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.

First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW

Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working over the oven door,but I am old. Good luck

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires nuts, (from last repair) installed new igniter. Not rocket science here.

Simple repair ,unplug unit,cut the 2 wires close to heating element,remove elements 2 screws w/1/4 inch nut driver. Cut and strip 2 wires back about 1/2 inch,be sure to cut wires close to element,wirenut both wires together. Reinstalled element,plug unit back in. Done . . . 12 Minutes,ready to bake a cake. .

First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--close the door and call for heat the gas valve is working fine now....

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!

Removed the storage drawer to access the door springs.Removed the worn hinges and installed the new hinges,connected the springs. Removed the oven door before anything else was done.The could not have been any simpler .

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?

moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.

Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripped wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.

Removed oven door. (two screws)
Removed racks.
Removed oven floor. (two finger screws)
Removed diverter (V) tray. (one nut)
Removed small panel @ left lower back of oven
(1 screw) to access elect. power disconnect.
Disconnected power.
Removed element (two square drive screws)
Snipped and stripped old wires, connected new
with ceramic wire nuts supplied.
Installed new element, reversed proceedure.
Oven lights in 10 seconds. Wife happy!
Probably 40 minutes, could do it again in15-20
once you know what tools to lay out.