FED300WAW3 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Elizabeth City, NC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged
snap out the old one and snap in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from El Dorado, AR
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bottom element broke and would not heat
the repair itself went smoothly. the clips that the new part connected to were old and slack. the clip came undone and had to pull the stove out to get to part from the back. i squeezed the clip together to make it stay on the new part and it held. the oven is heating well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from BROOKFIELD, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
element burned out
pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Storm Lake, IA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dead burner
I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Castle, PA
- Parts Used:
- 318372211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PRAIRIEVILLE, LA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Lexington, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element went out
Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Great Falls, MT
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element cracked.
First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from La Crescent, MN
- Parts Used:
- 316442301, 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out baking heating element in oven
Removed element by loosening two screws, disconnected heater element and connected new element and reattached to oven wall. Turn on oven to check for heater to work. Confirmed heater worked. Repair complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melody from Moberly, MO
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Oven Baking Element Burned Through Causing It to Break Into Two Pieces
First my husband removed the two screws that held the heating element into place. I had tried it with pliers which didn't work well. But with the proper socket the screws came loose easily. He pulled the heating element out a few inches and detached the wires. He then slipped the wire over the new heating element and screwed the new element into place. Now we can bake again. Very easy and we received the part quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Garrettsville, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element split and quit heating
If I didn't need my oven ASAP, I would not even have attempted to do this repair before my husband came home. But he wasn't going to be home for hours, and I needed it now!
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!
Thanks,
Vicki
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!
Thanks,
Vicki
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Fremont, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cooked things very SLOWLY.
Pulled old burner out, pushed new one in. WHAT A DIFFERENCE!! Heats very quickly, now.
Was this instruction helpful to you?
Thank you for voting!