FEF389WFSA Frigidaire Range - Instructions

Unpluged Oven, Removed 2 screws, unpluged Element, Plugged in new element. Replaced 2 screws, plugged oven in. Done 15 minutes.

Viewed the video and simply removed the two screws with a 1/4" nut driver, removed the existing bake element and installed the new one. Quick and easy, even for someone who is not mechanically inclined.

Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!

Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on

Took out 2 screws unclipped the part put the new one on and i was done. Very easy fix .. Baked a cake right after to celebrate

Watch the easy install video a couple of times and easy as a piece of cake!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the new element, reassembled and SHAZAM. It worked. I am not good with electrical circuit testing etc. even though I know it must be easy so after reading many stories here, I decided to start by replacing just the element and see if I got lucky. I did. No need to call expensive repairman.

I UNPLUGGED the oven (very important), then I removed the two screws that hold the element in place, pulled the element out far enough to disconnect the two wires, plugged the wires on to the new element, pushed the new element back into place, and replaced and tightend the two screws. Finally, I plugged the oven back in.

removed the two screws pulled the wires out sliped the connections from the old element and connected the new one .

Too dark to see, so left the power on so I cold use the oven light. Big mistake, shorted the fuse at the main box. No power in part of the house until finally figured out how to trip the fuse back on. Lesson learned. Never work on anything electrical without first turning off the power.

We called a local repair shop and they told us that it would take a month to get our part and it would cost over $50 for it. We went online and found PartSelect.com. The part was here in less than one week and it cost less than $40. My husband pulled the stove out from the wall took a screwdriver and unscrewed the screws, slipped in the new part and screwed the new screws in. It took him 15 minutes to fix it and now my stove works better than it has in many years!

Using small square tip screwdriver (#1 if my memory is correct), removed two screws at rear of oven pulled old element carefully by pulling, removed wire from each side, attached wires to new element, slid to back feeding wire back where they had been, put screws back in, tightened and viola, stove working great. Approximate time to do job, less than ten minutes!

I flipped the 220 circuit breaker to shut off the electricity. I unscrewed the old element (2 screws). One problem I ran into was that there was insulation packed tight around the old wire, so when I went to pull it out one of the connectors came undone. So I had to take the small plate off the back of the stove and fish the wire back through. I connected the new wires and screwed the element to the back. I only needed a square head screw-driver for the whole job. It would've taken me 5 minutes if I wouldn't have had to fish the wire back through. Still, it only took around 20 minutes and was really easy. The element cost me less than half of what an appliance repair shop charged. I'm a woman, and I've never attempted anything like this before but the video made it so easy to do! Thanks for saving me a bundle of money!

My part was the oven burner for my Tappan stove. I followed a very helpful you tube video. All I had to do was use 1/4" screw-type screwdriver (not sure what you call it), remove screw, pull out each side, pull part away from wire; and then insert the new oven burner!! SIMPLE and I'm a 68-year old widow! I was proud.

Removed the screws, replaced it with the new bake element, put the screws back in........and bam! I'm back in business. That's how easy this was to repair. Bake element cost me 40 bucks, appliance repair shop wanted about 200 bucks to repair.