FGF316DQD Frigidaire Range - Instructions

I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necessary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

replaced it

the igniter is real easy to put in

It went okay but I had to have some help putting it back together. One person held the glass while the other person tightened the screws.

Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.

Figured out which part we needed by reading about others problems; Followed instructions & Presto = oven heats!!!! Didn't have any problems removing or replacing part.

The repair shop wanted 150 dollars to fix it. I ordered the glass and replaced it myself. It was really easy and all I need was a screwdriver. It took me about 30 minutes total.

Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in oven, plug in and test.

after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com

Followed service sheet. Measured 2.6 amps draw at igniter wire which should have been 3.2 amps. Replaced igniter and problem resolved.

My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..

Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. After that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.

followed online instructions

I simply searched YouTube for the problem I was having and foud it was probably caused by a bad part. I found the part online and ordered it. It was as simple as a few screws and a couple wire-nuts to install. My girlfrind was very happy to get the oven fixed !!!!
Thanks parts-select for having pictures and dimensions so I was sure I had ordered the exact right part.
I was soooo happy to have found you !