FEF455WCBA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from CHESTERTOWN, NY
- Parts Used:
- 318255605
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
top electric burner not working
2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HAYDEN, AL
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cooktop burner was wore out from age
Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes
Was this instruction helpful to you?
Thank you for voting!
Drip bowels needed to be replaced
I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from GREELEY, CO
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heating element burned out
All you do it unplug the old one and plug in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pearland, TX
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element had burned out
Extremely easy. Two screws and electric connection that had easy pop on-off connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from NEW BADEN, IL
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven Bake Element caught fire
Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony J from HAMMONTON, NJ
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the burner stop working
Just followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from HIGH POINT, NC
- Parts Used:
- 318255006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Heating element broken
I followed the instructions from the lady taking my order she talked me through the steps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rockie from KEIZER, OR
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burnt out element
Followed instructions on website. Went perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Dayton, OH
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element burned out in my slide in range
Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from WEATOGUE, CT
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original Element physically broke
There is an installation video , but it was so easy, and if you clean your drip pans from those inevitable spills you can do this. I have zero mechanical abilities and I did. The website makes it easy to find your part, and the original literature you got with your appliance will direct you where to find the Model # and serial # on your Frigidaire Range. Order your part on line, get it in the mail and insert the Element yourself.Very happy with my transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conan from Moline, IL
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Two burners did not heat
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny L from CHELAN, WA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heavy jam boiler caused elements to sag
Removed the old & simply inserted the new one
Was this instruction helpful to you?
Thank you for voting!