FEF355ASH Frigidaire Range - Instructions

Pulled old burner out, pushed new one in. WHAT A DIFFERENCE!! Heats very quickly, now.

Switch was easy to replace. Some hex head screws to remove the panel and two screws to remove the switch. Though the plug in positions were totally different, all the quick connect terminals were marked on both switches.

I unplugged the damaged unit and plugged in the new one.

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

Remove two screws from bottom of inside oven door slide oven door up of hinges in side of door has 2 more screws when removing hold handle it does come off at very bottom of door remove all screws cover comes off remove new glass from package and place over brackets put oven door cover back on put screws back on slide back on bracket put last screws on

The drawer under the oven had been aggravating me for some time. It was titled and did not close right. Finally, I took it out to see what the problem was and noticed that the glides were broken. I googled the model no. of the stove (figuring I would have no luck) and to my great relief was directed to this EXCELLENT site. I ordered the new drawer glides within minutes and they were literally delivered the next day. Snapped right in, fixed, happy!! It's times like this when I can't figure out how we all lived without the internet!

removed back and transferred four wires to new part and replaced back

Just use flat screwdriver to press on clip and just squeeze it in

After researching on what exactly to call the part, which was a front drawer glide. I found this out by watching the video. It showed me exactly what I needed and what it looked like. I run to the oven to look at the other one, to make sure thats what I needed, and it looked like the part that I needed (mind you I am a female, and not a repair person), so this video helped me out alot. When the part arrived, I knew how to take the drawer out, and easily snapped the little plastic glide in to place, and slipped the drawer back on the gliders, and it worked perfect, so proud of myself, that I done it by myself, with no help from husband. I bragged and bragged on myself with a big pat on my own back, thanks Part Select, I know what to do when it happens again. Its my fault cause it broke, cause I overload the drawer with pots and pans LOL!!! Brenda Dixon

Removed the drawer. Inserted the new glide tab into a hole in the side. Inserted the drawer slides in the the glide. Closed drawer--done! Works fine. Probably only 5-10 minutes.

I removed the drawer, removed and replaced the guides on both sides in the front and replaced the drawer.

Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.

I had to replace the clock /power panel on the stove. It did not come with a face oover. Both installations were fairly east once the problem was diagnosed. The control part did not show a face plate not included, or needed. I had to reorder the overlay . The job came out perfect and my stove looks like new again.

First I unplugged the element that wasn't working and switched it with one that was to confirm that it was the burner element, and not the cooktop wiring, that was the problem. Once that was confirmed, I ordered a new element from partselect.com. Upon arrival of the new element several days later, I plugged it into the empty plug on the cooktop and voila, we're cooking on all 4 again.

On this website, I found an instruction manual for this stove. There were 2 pages about how to change the glass on the oven door, including diagrams. I'd also checked a generic youtube video on changing inner glass on oven doors too, although the hinges in the youtube demo weren't exactly like those in mine. I printed out the instructions, checked the oven door to make sure the hinges looked like those in the diagrams, set aside a couple of hours on a free day with no other distractions, and did the job. I just kept removing screws from the inside oven door, peeling back the layers of the onion, until I got to the innermost glass, which was cracked. Put the new glass in, put it back together. On youtube the guy said it would take 20 minutes. It took me about an hour. Saved a ton of money by doing it myself.