RS35BAW3 Frigidaire Range - Instructions

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device)
Plugged in new one and replaced screws to hold in place.

Removed the 2 element holding screws, disconnected the element leads & remover element. Replaced with new element.
All in all a real easy job (wish all repairs went this easy)
PartSelect had the element at the house within a couple days (Correct part I might add) which made the wife happy !!

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!

Removed back of stove, removed screws holding old element. attached new element in same place, returned back to stove. My wife pushed element from inside stove into holes, which was a help. Voila! It works great.

juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.

First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.

Just took the back of the stove off and removed old one and put new one in. Very simple.

I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.

Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.

Working on 33 year old Kenmore stove (Harvest Gold color bought in 1977). Have replaced the element every 12 to 14 years, last in 1997. 3-5 FedEx delivery took only 1 day. I verified Selector dial and Temperature dial both set to off. I took out the 2 oven shelves and took off the oven door for easier access to back of oven. Open oven door slightly to 1st catch, slightly lift and pull door away from the oven to clear the 2 side hinges from the openings. I used 1/4 inch socket with ratchet to remove 1 screw on each side holding element to back wall of oven. Gently pulled element out and up slightly so connectors come through openings in back wall. 1 connector came out from wall 4 inches, the other just barely. I used needle nose pliers to pull connector off element with 4 inches of wire. The connector did not come off easily, it took some wiggling of the connector (not too hard because it is brittle). I pulled connector off element barely out from the wall and held the connector in the pliers (did not let go). Put old element on kitchen floor and put new element on oven floor. Attached connector wire to end of element so it didn't slip through back wall. Attached connector wire to other end of element. Lifted element slightly to push through back wall openings. Used 1/4 inch socket to re-attached both screws. I put oven door back on (reverse of taking off). I set Selector to Bake and Temperature to 300. I watched element heat up (nice solid color along entire length) and reach 300 temperature and cycle off. I opened oven door to force the thermostat to kick in the cycle again. I closed oven door to watch the element again. When the heating cycle finished, I turned the Selector & Temperature to off. When oven cooled off, I put the shelves in again.

Took the back off, and took the terminals off. Took out the old element and put the new one in and put the terminals on and screwed it back in and put the back on. And all done.

The only difficultly I had was to bend down the ends of the new element so they were straight. Easily done with a pair of pliers. Slide the connectors from the oven over the ends, and put them back into the holes for them in the oven.Correct size socket and it was installed in minutes. I turned the oven on, and there was my heat. I used an oven thermometer to check the heat, and it was perfect. Quick service and the element was exactly the correct size.

first i removed the two screws that hold the element in place. then pulled out about 3 inches
and disconnected the wires.installed in reverse
order.