RGS35CL2 Frigidaire Range - Instructions

I'm a stay at home mom so when the oven didn't heat up I through oh no I have to get a new one. Well who can afford to get a new oven right after christmas. So I played with it to see if the other parts still worked, when I found that they did, I googled the the Appliance name, that is when PartSelect showed up and they had a video on how to replace the bake element. It looked doable so I ordered the part and it really was a easy fix. It took less than 10min all I had to do was pull out the old element and put in the new element. Only trouble I had was, I had to bend the prongs alittle but that was no problem. Thankyou PartSelect

Unplugged stove, use nutdriver, removed screws, pulled out old element, put in new one. Done. As prescribed. Excellent help as well as got part the next business day.

Just removed nuts. Pulled out the element from the unit. Disconnected each end. Reconnected new element. Pushed piece back into insulated unit. Attached nuts. Done.

We tested all of the other "functions" of the oven to make sure that everything else worked fine, and we realized that the problem really had to be the element.

We ordered it and it came within 72 hours! We simply unscrewed the faulty element, made sure that the wires were handled carefully (circuit turned off!), and inserted the new element and rewired and screwed back into place the screws that were removed.

Simple as pie! You can do this! You don't need a service call for this one guys! Get BRAVE!!

Had to drill 2 new holes 1/4 lower in oven so new coil would bolt up evenly besides that it went easily.

I unhooked element from wall on inside. Only two screws to undo. I then took back of stove off and unhook speaker like connectors. It was very simple.

Removed the elments2 screws, unhooked the two wires, removed the rear cover from back. I then installed the new element, covered the termanals with electric tape replaced the rear cover screwed down the new element, tested.

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Required taking back of stove off to properly extend the wires to plug in the new element as well as crimping existing plugs to obtain a secure contection.

At first I used a nutdriver to remove the two inside screws and found that one of the wires were not long enough to disconnect. I had to remove an access panel in the back which only had 5 screws to remove. I took it off, replaced the element and put it all back together. Then my wife tested it by baking an angel food cake which turned out perfect.