RES36BFL2 Frigidaire Range - Instructions

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.

I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.

The only difficultly I had was to bend down the ends of the new element so they were straight. Easily done with a pair of pliers. Slide the connectors from the oven over the ends, and put them back into the holes for them in the oven.Correct size socket and it was installed in minutes. I turned the oven on, and there was my heat. I used an oven thermometer to check the heat, and it was perfect. Quick service and the element was exactly the correct size.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.

They don't make appliances this easy to repair anymore. just as others say: screw out, unhook element ..hook new one to wires, screws back in.. you're DONE.. Thanks for great service and very quick delivery

Removed sheet metal plate from back of oven. Disconnected two lead from existing bake element. Removed existing bake element, replaced with new one. Connected wires, replaced sheet metal.

The trick with this old oven is to access the wires from the back.

Had to drill 2 new holes 1/4 lower in oven so new coil would bolt up evenly besides that it went easily.

I unhooked element from wall on inside. Only two screws to undo. I then took back of stove off and unhook speaker like connectors. It was very simple.

took off the back of the stove..first Unplugged it! and undid the old unit, and put the new one on....easy peasy!..Thanks for your fast mailing!

Just removed nuts. Pulled out the element from the unit. Disconnected each end. Reconnected new element. Pushed piece back into insulated unit. Attached nuts. Done.

I used this site self diagnostic page and ordered the oven heating element as that was the item suggested for repairs. It was the correct part to fix my oven problem. I had my electrician visiting to install two light fixtures so I had him install the new heating element in the oven. Even with him going to the garage to turn the circuit breaker off for the range the installation took less than 5 minutes.
This site is the greatest!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.