FED355DSB Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed new drip bowls
The hardest part of the job was cleaning under the old rings. Cook top looks new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sharon from Summerton, SC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element not heating right
Took old one out and plugged the new one into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lake Mary, FL
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Really easy to replace handle. However, because the new handle does not have the metal inserts to receive the attaching screws (!appearently a bit cheaper to make!), I am concerned that it will not last as long. I could find no reference to new attaching screws so used the old ones...hope it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Greencastle, PA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" left front surface element would no longer heat properly
I ordered the exact replacement element, and after unpacking it, it took about 5 minutes (actually,less; didn't time it), and the new element was installed and working fine.Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from North Smithfield, RI
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven did not work since bake element did not warm up.
Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Weatherford, TX
- Parts Used:
- 903136-9020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right large burner switch only heated on "high"
I mistakenly took the two screws out of the front piece above the oven. Except for that the time would have been maybe 10 minutes. The knobs all four came off easy and so did the retainer nuts and the six screws holding the metal plate. I took the old switch out after turning off the power. I had the new switch in one hand and removed one wire at a time from the old and put it on the new one. Put the parts back in place and turned the power on and turned the switch on. Works great! Saved about one hundred and thirty dollars from what the repair service charged last time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constantine from Vero Beach, FL
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower oven element burned up
Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorenza from Rowlesburg, WV
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Improper temperature when baking.
Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Artesia, NM
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Coil melted in half.
First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Glasgow, MT
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Union Point, GA
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element went out on my oven
Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Milford, IN
- Parts Used:
- 318394803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove door switch was broken
used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Reno, NV
- Parts Used:
- 316270201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke
unscrewed old and screwed in new
Was this instruction helpful to you?
Thank you for voting!