CGLEFM97DSJ Frigidaire Range - Instructions

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Talked to someone who knows , DX'd the potential problem,looked for the part on your very user friendly website and your DX was exactly what my oven was doing, when the Thermo-Sensor arrived, I unplugged the oven, removed the metal back, took out the faulty Sensor, replaced it very easy then realized the plug was different, so called a friend who knows how to Solder and 2 hrs, later, my oven was repaired and I began baking an Apple pie to repay a friends kindness The pie was perfectly baked , my friend was happy and so am I ,the baker, just before the holidays Thank you Parts Select for helpful DX and speedy delivery - seems you saved Christmas for me.

Removed outer glass first ,then worked my way thru to inner glass..

I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

I had order a replacement baking element to start, without trouble shooting the problem. When I had replaced the new bake element, set the oven to bake @ 350*F & watch for the baking element to heat up,it did not heat up. I waited for the oven to cool down,pulled the unit out & unpluged it from the receptacle.I removed the back cover,then I used my volt/ohm meter to check for contunity from the switch to both side of the element. Measured the ohms of the 3 bake elements,all good. Verfied that diodes were ok & there was no open resistors on the circuit board.No proble found. Put the back cover on, pluged the unit into the electrical outlet, pushed the unit back in placed, set the oven to bake @ 350*F, problem solved. My wife have bake several cakes & I cooked Sunday dinner using the oven. The real problem may have been an open circuit between the bottom bake elament & the switch. The repair was completed on 12/02/2012.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Removed the oven door, the trim was already cleaned and ready for new glass. Once the new part arrived, I removed it from the shipping container, placed it in the bottom groove of the trim kit and tightened the screws. Then placed the top trim and handle assembly, in place and tightened the screws. Then placed the oven door back on stove.

Removed power plug from outlet. Removed metal racks. Used 1/4" nut driver to remove screws. Carefully pulled element straight foreword. After wires were exposed they were carefully removed. Made sure wires stayed outside mounting hole. Put new element in made sure wires were secured to new element. Carefully push back on element to get wires in place. Put screws in element. Start one screw then the other. Then tighten both screws. Plug power cord back into wall" or turn circuit breaker on if you used that option. Turn dial to bake element on and check for prerogative operation.