FEFB68CQA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Hagerstown, MD
- Parts Used:
- 316270202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken oven door handle
I made the repair by removing two screws from the ends of the handle that were attached to the oven door and then reattaching the $88 plastic oven door handle with the same screws in the existing holes. At that price the door handle and I both got screwed very well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Minda from Madras, OR
- Parts Used:
- 316225001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The stupid baking element died on CHRISTMAS EVE!
My husband removed the old one in a few minutes, the just popped the new one in when it came. Not for nothing, (where we purchased the stove) wanted $67 for the same part you all charged $49.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Chicago, IL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Racks needed to be replaced.
Slide out the old; slide in the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederic from KILLEEN, TX
- Parts Used:
- 316555800
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Old element connections different from new element
Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center portion was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.
Was this instruction helpful to you?
Thank you for voting!
The front left dual element stopped regulating temperature
Replaced the dual element switch and that fixed it up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from fall river, MA
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Draw Glide Broken Off Bottom Drawer.
New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Armando G from Alice, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Electric burner switch shorted out.
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Forest, VA
- Parts Used:
- 316555800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Element Burn out
Self easy
PS Great service Super FAST.
Thanks Jesse
PS Great service Super FAST.
Thanks Jesse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fort Myers, FL
- Parts Used:
- 316203200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
broil element was bad.
It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from VESTAL, NY
- Parts Used:
- 316555800
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
One section of heating element failed to heat.
Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Elberon, IA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large burner wouldn't heat
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from CHICAGO, IL
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Error message on display ff30
Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed new ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Gaffney, SC
- Parts Used:
- 316203200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bottom elerment burnt into
First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from MORGANTOWN, WV
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
2 elements stopped working.
My husband followed the video instructions and it was easy to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!