FGF379WJCA Frigidaire Range - Instructions

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

1. Unplug the range to ensure there is no electricity running through the range. The repair can be done with the propane/gas line still connected.

2. If possible, remove the storage drawer for ease of access.

3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.

4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.

5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.

6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.

7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.

8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.

9. Reattach the drawer if necessary and plug the range back in.

10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.

It was a replace racks not repair. No problem

Unplug the range, remove racks. Remove 2 screws from the bottom back corners ( this was the hardest part. I used a stubby screwdriver, but a longer one would be better. They are fairly long screws). Remove oven bottom, lifting from the rear. Remove burner cover. Bottom left corner is a triangle cover. Remove this too. Remove the 2 screws holding the old igniter in place. The igniter unplugs easily. ( I used pliers, the plug has a clip, and pliers grip better.) Install new igniter ( it only fits in one way ) reinstall mounting screws and covers. Replace oven bottom. (I didn't replace the 2 screws. The bottom sits solidly, and they are a bit of a pain.) Plug in, set clock, test for oven to fire up.

It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.

It helps to remove the bottom drawer completely to gain easier access.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

switch out wires on spark module same burner would not lite
oder burner instead of igniter for four dollars more for new burner and igniter it made sense. Changed burner out burner works
thanks
Ron

Relatively easy to install once you get to the item.

Removed the front panel, top panel, original clock timer.
(15+ screws)
The leads were stuck and had to be pried out with a knife. As I removed one lead I inserted it into the same on the new panel.((eight leads various colors.)
One connector to remove and insert into new panel.
Done!!!! It worked!!! EXCEPT;
After putting it all together I discovered that the push buttons were not included with the unit. I had to pry out the old ones and reuse them on the new timer.

If it hadn't been for the push buttons the whole job would have taken about an hour.

Oh, just a reminder, turn off the eletricity. I forgot to and lit up a bit.

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

Very easy just had to pull the wire up that holds it secure.

I had to remove the whole back of the stove in order to gain access to the timer which is housed on the top console of the stove. There was 8 different leads and a wiring harness to keep track of. I had a friend help and after a good two hours we finally got it. I was never able to remove the top console so had to resort to a bit of prying to gain access to all of the screws. The manufacture did not make this an easy project. The part was rather expensive but with some thought and patients I now have a clock timer with a bright LED display with only one screw left over.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.