GG32CW3 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christy from North East, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven would not light
It was pretty much a plug in. My husband had it done in a few minutes. I want to thank you for your great service with receiving the part.
The oven is working great and now I am back to baking.
Thanks for everything
Christy
The oven is working great and now I am back to baking.
Thanks for everything
Christy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Inlet, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
igniter would heat up but burner for oven wouldn't
Took the two nuts off that hold the igniter and cut the wires as per directions and used the wire nuts to put them together after I installed the igniter.was a piece of cake and didn't take 15 minutes to do.Oven works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick E. from Washington, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
oven would not light
I just sent in a generic description of my problem and a couple of ideas on what it might be. Within 2 days an online repair person answered me back with the solution. I ordered the part and 2 days later I was back in business and baking cookies.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cornelius from Chicago, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Igniter would glow but no gas would come out
First I removed the bottom plate of the oven to get a better view. I then removed the burner plate and the burner. Disconnected the igniter and put in new one it was real simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from mayport, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
oven would glow but would take a long time to light, and you could smell gas
the igniter is real easy to put in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Los Angeles, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No heat, gas smell in oven
Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sean from spring grove, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
There was a glow in the oven but the oven wouldn't heat up
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconected the two wires. Take the old element out, and attach the new one. Assemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Warwick, RI
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not heat up.
could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from newport beach, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
no flame
removed the old igniter, installed the new one. 15 minutes, piece o cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Bremerton, WA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Had a problem igniting the gas.
took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- crystal from philadelphia, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
oven stopped lighting!!
wonderful went perfect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Shunk, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven wouldn't light or very slow to light
Removed the two screws, took out the old one and replaced the new one. It was very easy and the oven works great now. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Conneaut, OH
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Oven would not light; gas odor
This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repaired our stove myself!
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repaired our stove myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary Warren from Alexandria, VA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven was slow to light, strong gas smell, long time to reach set temperature
Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.
It was a snap!
It was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Macomb, MI
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
My oven would glow, but wouldn't heat.
I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
Was this instruction helpful to you?
Thank you for voting!