FES355ASC Frigidaire Range - Instructions

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first

Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Pulled out stove, took side panel off on switch side of oven, unplugged old switch, pulled the old switch out the front of the oven, put in new switch and plugged it in. Then put oven back together and pushed it back into space. (Make sure to turn oven off at breaker box before you make repair) you could easily get shocked if you don’t.

I determined that the failure was due to age and wear on the element. Therefore I thought it wise to replace all four burners as a preventative measure. First unplug from power! Replacing the burners was plug-and-play simple. Replacing the switch was easy: Remove the back panel, pull the control knob and remove the two screws securing the switch. Move the terminals to the new switch (one at a time) and mount it with the two screws and replace the back panel. NOTE: The foot bracket on the large burners were about 1/32" too stout and the burner element would not seat in the ring properly. I made a slight adjustment with my grinder and everything fits perfectly.

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

Broil worked on the stove, however in bake mode, the oven did not make temperature. Turned off the stove, unscrewed and inspected coil. I noted there was a section of the coil that had a "corroded" appearance. (it was evidence of the coil being burned out). Checked with a ($9.00) voltmeter, showed infinite resistance. Found the original envelop for the stove taped to the back of the oven from 1973. It has wiring diagram with schematic and noted the coil was 3000 W, 19 ohms.

Bottom Line found comparable replacement online and tested resistance, measure dimensions of the old coil, matched with Watt rating, replaced, tested installed and works great, Oven has been in use for a couple weeks now. New stove would have been around $500.00. Not to mention some remodel work, as the house is old and stove is a built in.

Coil was $60.00 and should buy the time I need until I remodel the entire kitchen.

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Took out the bad element and replaced it with the new element in less than 5 minutes, worked perfect, thanks

Just placed the chrome bowl trays in place and was good to go. They look very nice.

Generally straight forward repair with the most difficulty coming from the screws holding the element in place being rusted. Took some wd40 and some snub-nosed pliers to get them out. The wire connections on the back of the element are pretty self explanatory. Lightbulb was an easy change though the bulb connection had also rusted a bit and required some pliers to remove.

searched on the computer for the name and part number that was damaged, found that it was the bake element so i ordered it with part select.com. when it arriver three days later (as expected) i disconnected the gas and electric to the range and simply removed the old element with a phillips screw driver. installed the new element, hooked the gas and electric back up and began cooking again...

thanks partselect..