R530DL0 Frigidaire Range - Instructions

replaced old drip bowls with new ones

Repair was simple. Unplugged stove, removed a plate from back of stove. Disconnected wiring. Removed screws from inside oven, removed old element, installed new element. Replaced screws, hooked up wiring, replaced back plate, plugged it in, used it that night.
Thanks for sending the right part the first time and getting it shipped so quickly.

First shut power to oven off, removed the oven door and oven racks. Removed the 2 screws from the back of the oven holding the element in place. Slowley pulled the element out and removed the wires, pulled off with my fingers. Replaced the old with the new in the reverse order. Saving the Wife a pile of money.

Thank You,
Jerry R

followed your directions - excellent

Removed the baking element with a nutdriver. Slid it to the front of oven and removed the contacts on the back side. Installed the new element and installed the contacts at back of element. Slid it in the holes on back inside of oven and used a nutdriver to install the screws. It was very simple to do.

First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!

Unplugged the element and the melted on pot. Plugged in the new element. I thought I might need a whole new cooktop but a new element was very easy to find online.

unplug old baking element using socket tool and put in new baking element - very simple and it works!

First I removed the 2 screws on each side of the element and then pulled the element out, disconnected the 2 wires that were holding the element, got the new element and connected it to the wires, slid back into position, put the screws back in that hold the element and put the racks back in and turned on for test. It was so easy I had it done before my husband arrived home from work.

Took the back panel off. Removed the 2 screws from the old element,removed it. Put the new one in and replaced the screws. Put the back panel on done. What took the longest was cleaning behind there !!

Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device)
Plugged in new one and replaced screws to hold in place.

First I unplugged the element that wasn't working and switched it with one that was to confirm that it was the burner element, and not the cooktop wiring, that was the problem. Once that was confirmed, I ordered a new element from partselect.com. Upon arrival of the new element several days later, I plugged it into the empty plug on the cooktop and voila, we're cooking on all 4 again.

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

Removed the 2 element holding screws, disconnected the element leads & remover element. Replaced with new element.
All in all a real easy job (wish all repairs went this easy)
PartSelect had the element at the house within a couple days (Correct part I might add) which made the wife happy !!

I just had to plug the new burner plate in the receptical
and it works again very well.