PLEFMZ99ECN Frigidaire Range - Instructions

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

I am a DIY kind of wife. My husband works late most nights and I get home in the afternoon. It was really quit simple except for the element plug slipped into the back of the stove. So I had to pull the stove out from the wall and take a couple of screws out of the back and push the plug back through. It was scarry for a minute but it all ended up just fine and we had a wonderful dinner that night.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

repair was exceptionally easy. Did not need the fiberglass tape that was mentioned in online repair steps. Just slipped the wires off and then back on the new element. Any 70 year old can do.

Quite easy: Removed the two hex head screws with a 1/4 inch nut driver. Gently pulled the old element out of the rear of the range with the connectors still attached. Next I disconnected the connectors from the element and attached a small "paper binder" clip to each of the connector wires to keep the connectors from pulling back through the "Hole". Lastly, I connected the two connectors to the new element (released the clips) and gently pushed the unit back into place and re-secured the hex screws. ALL DONE! Very very easy....

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved

I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.

Oven is working great now.

Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.

If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.

Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.

Thanks

turned power off at fuse box took of back panel about8-10 nuts unhooked wires with pliers that went to element then took2 nuts out that held element up and 2nuts holding element took out and put new one in works great

Went well, and working thank you ??

Remove screws from back of oven after unplugging oven. disconnect wires from element by sliding of element. Remove screws holding element inside oven and slide element out. Replace element by doing everything in reverse. 20 minutes tops.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

first the temperature sensor then the igniter. started to do the igniter by using common sense then I used YouTube which made it a lot faster.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.

We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.