FGF365MXFCA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 316575501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Trim
The top of the door trim broke causing the side and glass to be loose. Easy fix by removing the broken trim and installing the new one.
Approximately 2 minutes to replace.
Approximately 2 minutes to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Castle Rock, CO
- Parts Used:
- 316490001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would kick off after preheating to temp.
Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Farmingdale, NY
- Parts Used:
- 316220002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost the metal clip inside the knob. so knob was loose
I compaed price at different sites and partselect .com was 30% cheaper for the same item. I received the part in 2 days by fed-ex.
Doing the job was real easy.Just pull the old knob out and put the new one in.
Doing the job was real easy.Just pull the old knob out and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Brunswick, GA
- Parts Used:
- 316445501
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven light stayed on & smelled like electrical burning.
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Warsaw, VA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken lens over oven light
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neeru from Princeton, NJ
- Parts Used:
- 316237704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
The bolts holding the readburner were rusted and broke
The range top had to be taken off along with the front panel to get access to the place the burner pipe connects. It took more time to unassemble and assemble the range than repacing the burner. The only issue was that the burner was sent without the bolts that will hold it in place so I had to go to local hardware store to get appropriate bolts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garland Futrell from CHESAPEAKE, VA
- Parts Used:
- 5304503232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Broken ; oven door inner glass
Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melinda from Three Rivers, MA
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Rusted leveling foot
I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lamoni, IA
- Parts Used:
- 316400603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burnt in aluminum foil...unable to remove
took the two screws out by hand, slipped out the ruined panel, slid the new one in place, replaced the two screws...simple as that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from ROCKVILLE CTR, NY
- Parts Used:
- 5304509983
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Circuit breaker tripping due to short circuit in the appliance.
After turning the power off and once I removed the back panel to access the wiring, the soot at the contact point of the short circuit was easily visible. It was the oven bulb socket that had come loose and caused the problem. I insulated the wire at the terminal point and reattached the fixture. All in less than 15 minutes.I turned the power back on and now it's good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Reading, PA
- Parts Used:
- 316220002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost the metal part inside snob and it was loose.
Simple. Removed the old ones and pushed the new knobs on. Took about 2 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from CANYON LAKE, TX
- Parts Used:
- 5304498835
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The seal around the oven door had frayed on the end and come loose.
We carefully pulled the old seal out of the door ( staples hold it in place).Then took the replacement and laid it around the door. Starting at one side we adjusted the seal and pushed the staples into place. Making sure we folded the ends, we used a spoon to push them into the slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from CLINTON TWP, MI
- Parts Used:
- 316404400
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Replaced Bake Burner Tube on Frigidaire Gas Range Model FGGF3058RFC
The installation of the bake burner tube went well. I followed the instructions within the Video as it pertains to replacing the Bake igniter. That video also describes the removal and replacement of the bake burner tube. The original screws that mounted the igniter to the burner tube bracket were damaged. I replaced them with 18-8 Stainless Steel Serrated-Flange Hex Head Screws, 8-32 Thread Size, 3/8" long. As noted in the video, the oven bottom panel is removed using a flat head screwdriver. For all other screws I used a 1/4" socket and ratchet. A Nut Driver would have also worked just as well. On initial start-up after the repair there was a minor light odor from the flame coming into contact with the new metal burner tube that dissipated within a few moments. In all everything went very well.
Was this instruction helpful to you?
Thank you for voting!